manualshive.com logo in svg

Vacon NX, Руководство пользователя

Vacon NX - это мощный преобразователь частоты, предоставляющий быструю помощь с помощью бесплатного руководства. Скачайте руководство с нашего сайта для получения подробной информации о продукте. {Website} - ваш источник полезных ресурсов для вашего оборудования.

Поделиться
Скачать
background image

Electrical cabling and connections

vacon • 81

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

6

6.1.1.5

Cable selection and unit installation in accordance with the UL standards

To meet the UL (Underwriters Laboratories) regulations, use a UL-approved copper cable with a 

minimum heat-resistance of +90 °C to meet the requirements.

Use Class 1 wire only.

The units are suitable for use on a circuit capable of delivering not more than 100,000 rms 

symmetrical amperes, 600 V maximum, when protected by J, L or T Class fuses.

Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit 
protection must be provided in accordance with the National Electric Code and any additional local 
codes. Branch circuit protection provided by fuses only.

6.1.2

Drive protection – Fuses

In order to protect the drive from short-circuits and excessive loads, input line fuses must be used. 
The warranty becomes void if the drive is not equipped with approriate fuses.

Depending on the drive configuration, the following types of fuse protection are recommended:

AC drive with AC supply:

Always protect the drive with fast-acting input line fuses for short-circuit protection. Also pay 
attention to protection of cables!

Common DC bus:

•

Inverter units: Choose fuse protection according to Table 43 and Table 44.

•

Active Front End (AFE) units: Choose DC fuses according to Table 43 and Table 44; 
Appropriate fuses for the AC supply are listed in Table 62 and Table 63, see Chapter 10.

•

Inverter units connected to AFE units: Choose fuses for AC supply according to Table 62 and 
Table 63;  

NOTE! 

Protect each inverter unit with fuses according to Table 43 and Table 44.

DC links interconnected (e.g. 2*CH74)

In case interconnection of DC links is required, contact the manufacturer.

Brake chopper unit

See Chapter 11.

6.1.3

Fuse sizes

The fuse sizing in the tables below is based on Ferraz aR fuses. We primarily recommend you to use 
these fuses or corresponding Bussman aR fuses (see Appendix 3 on page 196). Sufficient protection 
against short-circuit cannot be guaranteed if other fuse types are used. Furthermore, equation of 
the fuse values given in the tables below with those of other fuse manufacturers is not allowed. In 
case you wish to use fuses of other fuse manufacturers, contact your nearest distributor.

Содержание NX
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX

KEENZ Class Instruction Manual preview
Class
Бренд: KEENZ Страницы: 24
Tapeswitch C6 Technical Manual preview
C6
Бренд: Tapeswitch Страницы: 13
Baccara G75-DFC Installation Operation & Maintenance preview
G75-DFC
Бренд: Baccara Страницы: 16
BABYSTYLE OYSTER Instruction Manual preview
OYSTER
Бренд: BABYSTYLE Страницы: 8
BABYSTYLE Hybrid 2 Manual preview
Hybrid 2
Бренд: BABYSTYLE Страницы: 32
Jedo Trim User Manual preview
Trim
Бренд: Jedo Страницы: 26
HandyTrac Key Control Easy Manual Installation And Operation preview
Key Control
Бренд: HandyTrac Страницы: 14
TA STA Quick Start Manual preview
STA
Бренд: TA Страницы: 6
TCi 18055 Manual preview
18055
Бренд: TCi Страницы: 9
Panasonic KX-A16B Quick Start Manual preview
KX-A16B
Бренд: Panasonic Страницы: 8
Data Signs PTL Compact 2 Operation And Maintenance Manual preview
PTL Compact 2
Бренд: Data Signs Страницы: 23
Finnleo SaunaLogic SL2 Control Manual preview
SaunaLogic SL2 Control
Бренд: Finnleo Страницы: 14
M-system R7M-CT4E Instruction Manual preview
R7M-CT4E
Бренд: M-system Страницы: 7
Texecom premier 60ixd Installation Manual preview
premier 60ixd
Бренд: Texecom Страницы: 21
RAK WisBlock RAK19012 Quick Start Manual preview
WisBlock RAK19012
Бренд: RAK Страницы: 12
Cypress Semiconductor CY8CKIT-015 Manual preview
CY8CKIT-015
Бренд: Cypress Semiconductor Страницы: 36
Nabco GYRO TECH Nabco Multi-Module Manual preview
GYRO TECH Nabco Multi-Module
Бренд: Nabco Страницы: 21
DEUTSCHMANN AUTOMATION LOCON 100 Instruction Manual preview
LOCON 100
Бренд: DEUTSCHMANN AUTOMATION Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды