manualshive.com logo in svg

Vacon NX, Руководство пользователя

Vacon NX - это мощный преобразователь частоты, предоставляющий быструю помощь с помощью бесплатного руководства. Скачайте руководство с нашего сайта для получения подробной информации о продукте. {Website} - ваш источник полезных ресурсов для вашего оборудования.

Поделиться
Скачать
background image

8

vacon • 144

Commissioning

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

8.2

Commissioning of the AC drive

1. Read carefully the safety instructions in Chapter 1 and follow them.

2. After the installation, pay attention:

-

that both the AC drive and the motor are grounded.

-

that the mains and motor cables comply with the requirements given in Chapter 6.1.1.

-

that the control cables are located as far as possible from the power cables and that the 

shields of the shielded cables are connected to protective earth 

. The wires may not 

touch the electrical components of the AC drive.

-

that the common inputs of digital input groups are connected to +24 V or ground of the I/O 
terminal or the external supply.

3. Check liquid cooling connections and system operation.

-

open the shut-off valves

-

check the quality and quantity of the cooling liquid (Chapter 5.2)

-

ensure the proper operation of liquid circulation system

4. Perform the cable and motor insulation checks, see Chapter 6.1.10.

5. Check the AC drive for condensation.

6. Check that all Start/Stop switches connected to the I/O terminals are in Stop-position.

7. Connect the AC drive to mains.

8. Set the parameters of group 1 (See VACON

®

 All in One Application Manual) according to the 

requirements of your application. At least the following parameters should be set:

-

motor nominal voltage

-

motor nominal frequency

-

motor nominal speed

-

motor nominal current

You will find the values needed for the parameters on the motor rating plate.

9. Perform run test without motor

Perform either Test A or Test B:

A Controls from the I/O terminals:

a)

Turn the Start/Stop switch to ON position.

b)

Change the frequency reference (potentiometer).

c)

Check in the Monitoring menu (M1) that the value of Output frequency changes according 

to the change of frequency reference.

d)

Turn the Start/Stop switch to OFF position.

B Control from the control keypad:

a)

Change the control from the I/O terminals to the keypad as advised in Chapter 7.3.3.1.

Содержание NX
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX

Aaeon COM-KB Manual preview
COM-KB
Бренд: Aaeon Страницы: 76
Eaton ELC-COENETM Instruction Sheet preview
ELC-COENETM
Бренд: Eaton Страницы: 6
Eaton InsulGard Installation And Start Up Manualline preview
InsulGard
Бренд: Eaton Страницы: 35
Eaton xStorage Home User Interface Manual preview
xStorage Home
Бренд: Eaton Страницы: 18
Eaton DF6000 Application Manual preview
DF6000
Бренд: Eaton Страницы: 73
Eaton DALI Installation Manual preview
DALI
Бренд: Eaton Страницы: 4
Eaton Cutler-Hammer IQ DP-4000 Installation, Operation And Maintenance Instructions preview
Cutler-Hammer IQ DP-4000
Бренд: Eaton Страницы: 87
Eaton Char-Lynn Manual preview
Char-Lynn
Бренд: Eaton Страницы: 14
Eaton BiWire Flexi Installation Manual preview
BiWire Flexi
Бренд: Eaton Страницы: 36
Vageo DT-1 Plus Manual preview
DT-1 Plus
Бренд: Vageo Страницы: 2
Vacon 100 INDUSTRIAL Additional Installation Instruction preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 6
Vacon 100 INDUSTRIAL Technical Manual preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 24
Vacon 100X series Marine Installation Manual preview
100X series
Бренд: Vacon Страницы: 30
Vacon 100 flow User Manual preview
100 flow
Бренд: Vacon Страницы: 81
Vacon 100X series Installation And Maintenance Manual preview
100X series
Бренд: Vacon Страницы: 100
Vaillant VRT 340f Operating Instruction preview
VRT 340f
Бренд: Vaillant Страницы: 32
Vaillant VRT 330 Manual preview
VRT 330
Бренд: Vaillant Страницы: 27
Vaillant VRC 470 Operating Instructions Manual preview
VRC 470
Бренд: Vaillant Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды