Thermo Scientific 074114 страница 88 Скачать руководство пользователя

Страница: 88 / 148

Dionex PDA Operator’s Manual

Doc. 065378-01 1/12

f. Reinstall the cell in the optical bench.

g. Autozero the detector again to verify that the problem has been

resolved. If the error message appears again, contact Thermo
Fisher Scientific for assistance.

If the lamp intensity reading is below 10 million counts for a standard or
semi-preparative cell

below 3 million counts for a semi-micro cell,

follow these steps:

a. Check that the flange of the deuterium lamp is aligned with the

two locating pins in the optical bench (see

Section 5.3

). If the

flange is aligned, the lamp is defective and should be replaced
(see

Section 5.7

b. If the error message appears again, contact Thermo Fisher

Scientific for assistance.

•

Filter paddle has malfunctioned

Check the Chromeleon Audit Trail. If the “Filter wheel sensor could not
detect blocked position.” or “Filter wheel sensor could not detect open
position.” message is displayed, see

page 66

for instructions.

•

Failure of an electronics component

Turn off the Dionex PDA power and contact Thermo Fisher Scientific for
assistance.

NOTE Do not attempt to service the Dionex PDA electronics

components. All repairs of the electronics components
must be performed by Thermo Fisher Scientific
personnel.

4.8

Wavelength Calibration Fails

•

Deuterium lamp may be defective

If the

DEUTERIUM – UV

LED is flashing rapidly—or if the LED fails to light—

replace the deuterium lamp (see

Section 5.7

If the

DEUTERIUM – UV

LED is lighted but is not flashing, open the Dionex

PDA Wellness panel and run the wavelength calibration and the wavelength
verification test (see

Section 4.14.2

). If the Dionex PDA fails these

procedures, remove the flow cell from the detector and repeat both

Содержание 074114





















































































































































Результаты поиска

Содержание 074114

Отзывы:

Похожие инструкции для 074114

Бренды по названию

Популярные бренды

Thermo Scientific 074114, Руководство оператора

Результаты поиска

Содержание 074114

Отзывы:

Похожие инструкции для 074114

Бренды по названию

Популярные бренды