Thermo Scientific 074114 страница 121 Скачать руководство пользователя

Страница: 121 / 148

B • Installation

Doc. 065378-01 1/12

113

B.3 Installing the Flow Cell

1. Grasp the Dionex PDA front cover by the sides and pull straight off to

remove.

2. Remove the flow cell cover from the inside front panel (see

Figure 2-3

Standard or semi-micro cell

: Remove the tubing bracket from the lamp

cover (see

Figure 5-1

4. Squeeze the handle of the flow cell and insert it straight into the optical bench.

Release the handle, and then pull it forward slightly. If there is a click, the cell
is properly mounted. If there is no click, rotate the handle slightly just until
the cell clicks into place.

5. Thread the flow cell inlet tubing through the tubing guide on the lamp cover

and reinstall the tubing bracket (see

Figure 5-1

6. Thread the flow cell outlet tubing through the slot on the side of the flow cell

cover. Replace the cover and reconnect the cell inlet and outlet tubing.

Standard or semi-micro cell:

Connect the cell inlet tubing to the reducing

union fitting (P/N 055903 for a PEEK cell; P/N 055902 for a stainless steel
cell) on the heat exchanger tubing (see

Figure B-1

Do not touch the cell windows. If you touch a window, clean it with
isopropyl alcohol (IPA) and a clean lens tissue.

Do not use a PEEK flow cell with normal phase or chlorinated
solvents; these solvents will damage the cell.

Do not use a stainless steel flow cell with low pH solutions; these
solutions may cause corrosion, contamination, and metal leaching.

Содержание 074114





















































































































































Результаты поиска

Содержание 074114

Отзывы:

Похожие инструкции для 074114

Бренды по названию

Популярные бренды

Thermo Scientific 074114, Руководство оператора

Результаты поиска

Содержание 074114

Отзывы:

Похожие инструкции для 074114

Бренды по названию

Популярные бренды