manualshive.com logo in svg

Siemens SIMOTION D4x5-2, Руководство по эксплуатации, Страница: 98 / 446

Поделиться
Скачать
Siemens SIMOTION D4x5-2 Скачать руководство пользователя страница 98

Table 4-20

Status word "ZSW1_Common_PLC"

Bit

Signal name

Remark

0

CAMERA_OK

Camera OK
 
0: The measured values from the camera (SIMOCRANE CenSOR) are in‐

valid or communication is down.
1: The camera (SIMOCRANE CenSOR) is supplying valid values and com‐

munication is up.
Note:
This status bit is not interconnected via the DCC_SCCOMMON DCC block.

1

CHANGE_TARGET

Change target
0: Target is the hopper
1: Target is the ship
This status bit is only relevant when GSU is selected (P102=0).
With on-the-fly unloading: Once the trolley velocity is less than the "on-the-fly 

unloading abort velocity" (P30), the OPEN_GRAB status bit is reset. A new 

target (ship) can be specified. The "CHANGE_TARGET" bit is to be used for 

this.
The bit is always set via the landside target, irrespective of on-the-fly un‐

loading.

2

NO_WAIT_POS_OK

Waiting position is not approached

Confirmation of the general NO_WAIT_POS control bit.

3

LEARN_PROFILE_ON_OK

Height profile learned

Confirmation of the bit for "LEARN_PROFILE_ON" mode.

4

LEARN_PROFILE_RESET_OK

Height profile deleted

Confirmation for the deletion of the internally learned variable obstacle re‐

gions (height profile). The height profile has been deleted.

5

START_AUTO_OK

Start in SAM mode permitted

Bit for

 

enabling SAM mode without triggering an error message. An exact 

explanation why a start is not possible can be seen in Table "INFO_NO_AU‐

TO_START" (see below). A group bit can also be formed from signal mes‐

sages by the PLC. In this way, specific functions can be permitted for SAM 

mode (e.g. start from slack rope on the waterside). 

6

HOIST_TAKEOVER_OK

Hoist takeover permitted

This bit is set when the hoist is located above the highest obstacle in the 

positioning direction. Manual hoist takeover is therefore possible. If this bit is 

not set, no manual control for the hoist may be permitted during travel in SAM 

mode. A collision with obstacles could occur. 

7

OPEN_GRAB

Open grab

0: Do not open grab

1: The grab can be opened
This status bit is only relevant when GSU is selected (P102=0).
This bit is used as a control signal for opening the grab. The time of setting 

is specified by parameter P31; the time of resetting is specified by parameter 

P30.

OPEN_GRAB is only set if on-the-fly unloading (FLYING control bit) is acti‐

vated and if selection "3" is activated in parameter P152. 

Communication interface to SIMATIC S7
4.2 SIMOTION D for AddOn → SIMATIC S7

SC integrated STS, GSU

98

Operating Instructions, 07/2019, A5E48271265B AA

Содержание SIMOTION D4x5-2































































































































































































































































































































































































































































Отзывы:

Нет отзывов