manualshive.com logo in svg

SCIEX TripleTOF 5600, Руководство пользователя системы

Поделиться
Скачать
SCIEX TripleTOF 5600 Скачать руководство пользователя страница 41

• If the device uses 

Ethernet

 as a communication interface, then type the 

IP Address

 assigned to the

device by the administrator or use the corresponding 

Host Name

 for the address.

• If the device uses 

GPIB Board

 as a communication interface, then do not change the settings for the GPIB

board.

The rest of the preset values for the device are probably appropriate. Do not change them. For information
about the Configuration and Communication tabs, refer to the Help.

10. To restore the device preset values, on the Communication tab, click 

Set Defaults

.

11. To save the configuration, click 

OK

.

12. Repeat step 

 4

 to step 

 11

 for each device.

13. Click 

OK

 in the Create New Hardware Profile dialog.

14. To activate the hardware profile, in the Hardware Configuration Editor, click the hardware profile.

15. Click 

Activate Profile

.

The check mark turns green. If a red x is shown, then there is an issue with the hardware profile activation.
For more information, refer to 

Troubleshoot Hardware Profile Activation on page 41

.

Tip! 

An active hardware profile does not have to be deactivated before another one is activated. Click an

inactive hardware profile and then click 

Activate Profile

. The other profile is deactivated automatically.

16. Click 

Close

.

Troubleshoot Hardware Profile Activation

If a hardware profile fails to become active, then a dialog opens indicating which device in the profile failed. A
device might fail to activate because of communications errors.

1. Read the error message generated. Depending on the message, there might be an issue with a device or how

the communication is set up.

2. Verify that the device has power and is turned on.

3. Verify that the COM port assigned to the device is correct.

4. Verify that the communication settings for the device (for example, dip switch settings) are set correctly and

match the settings on the Communication tab.

5. Turn off the device.

6. Wait 10 seconds.

7. Turn on the device.

Wait until all device power-up activities are complete before trying to activate the hardware profile again.
Some devices might require 30 seconds or more to complete the power-up activities.

TripleTOF

®

 5600/5600+ System

System User Guide

41 / 131

RUO-IDV-05-7040-B

Operating Instructions — Hardware Profiles and Projects

Содержание TripleTOF 5600




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды