manualshive.com logo in svg

Savch S900 Series, Руководство пользователя

Поделиться
Скачать
Savch S900 Series Скачать руководство пользователя страница 47

 

  44

 

Function List 

Set 

value 

Description of function 

d 0 

No function   

d 1 

Inverter running.  If  output  occurs  to  inverter,  output  terminal  contactor  which  sets  this  parameter  shall  be 

CLOSED. 

d 2 

Frequency  arrival.  When  output  frequency  of  inverter  agrees  with  set  frequency,  this  contactor  shall  be 

CLOSED. 

d 3 

Zero speed. When inverter set frequency is less than Min starting frequency setting, this contactor shall be 

CLOSED. 

d 4 

Over-torque detection. This contactor shall be CLOSED when over-torque is detected by inverter.   

d 5 

During external alarm. This contactor shall be CLOSED when external alarm happens to inverter. 

d 6 

Low voltage detection. This contactor shall be CLOSED when input voltage over-low is detected by inverter.   

d 7 

External terminal running mode. This contactor shall be CLOSED when inverter reference is controlled by 

external terminals.   

d 8 

Alarm output (for any alarm). This contactor shall be CLOSED when fault is detected by inverter. 

d 9 

Frequency  detection.  This  contactor  shall  be  CLOSED  when  output  frequency  agrees  with  appointed 

reference (3-00). 

d 10 

During pattern operation. This contactor shall be CLOSED when pattern operation performed.     

d 11 

Pattern  operation  one  cycle  completion.  During  pattern  operation,  this  contactor  shall  be  CLOSED  after 

each running step, but it shall maintain only for 0.5sec. 

d 12 

Pattern operation completion. This contactor shall be CLOSED after completion of pattern operation, but it 

shall maintain only for 0.5sec. 

d 13 

Pattern  operation  pause.  This  contactor  shall  be  CLOSED  when  external  pause  pattern  operation  is  in 

action during program auto running. 

d 14 

Terminal count value arrival. This contactor shall be CLOSED when count value is equivalent with set value 

of Parameter 3-01. 

d 15 

Terminal  designated  count  value  arrival. This contactor  shall  be  CLOSED  when  count value  is  equivalent 

with set value of Parameter 3-02. 

d 16 

Inverter ready to run. This contactor shall be CLOSED if no alarm was detected after motor drive power is 

supplied. 

d 17 

Fwd  running.  When  inverter  is  in  fwd  run,  delay  reference  time  shall  be  in  accordance  with  setting  in 

Parameter 3-03, and contactor shall be CLOSED when time met. Relay shall be interrupted when inverter 

stops or is switched to Rev run stations. Attention shall be paid that counting here shall begin from Fwd run. 

d 18 

Rev  running.  When  inverter  is  in  Rev  run,  delay  reference  time  shall  be  in  accordance  with  setting  in 

Parameter 3-04, and contactor shall be CLOSED when time met. Relay shall be interrupted when inverter 

stops or is switched to Fwd run stations. Attention shall be paid that counting here shall begin from Rev run. 

d 19 

Fwd/  Rev running  direction.  This  reference  shall  be  available  at  switching  of  Fwd/Rev  run.  Description  of 

action:  During  direction  switching  of  motor  drive,  the  relay  shall  be  Opened  and  then  delayed  in  a  time 

complied with setting in 3-03 and 3-04. After delay, the relay shall be closed. Provided that delay setting in 

3-03 and 3-04 is 0, relay shall be kept in closed condition and not open until machine stop signal appears. 

Notes:   

1.“CLOSED” mentioned above refers to closing of normally open contactor(RA-RC), and normally closed contactor 

(RB-

RC) shall open simultaneously; while “open” shall refer to opening of normally open contactor(RA-RC), and 

normally closed contactor(RB-RC) shall be closed simultaneously. 

Содержание S900 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды