Savch S900 Series Скачать руководство пользователя страница 45

Страница: 45 / 86

2-10

Rotation direction inhibition

Factory setting

d 0

Setting range

d 0: Fwd / Rev run available

d 1: Rev run inhibited

d 2: Fwd run inhibited

If parameter is set to d1” Reverse run inhibited”, REV reference of both the operation keypad and external terminals

shall be unavailable. Even if Rev Run is performed currently, it shall be switched to fwd run directly. Also, provided

that fwd run is inhibited, only Rev run reference shall be performed.

2-11

Reference loss detection(Terminal ACI)( stop mode)

Factory setting

d 0

Setting range

d0: Non-processing

d1: Coast to stop

d2: EF display after deceleration stop

d3: Continuous operation by reference frequency before disconnection

Treatment to reference of 4~20mA (ACI) broken line is determined by this parameter. If it was set to d2 and fault

occurs, press MODE/RESET to reset after alarm is eliminated.

2-12

Power on start

Factory setting

d 0

Setting range

d 0: Operation available

d 1: Operation unavailable

When operation reference is from external terminal and operation reference is always in kept station, and when

power supply of inverter is starting, this parameter is to determine operation status of motor. If it is set to d0,

operation reference shall be accepted and motor begin to run; if it is set to d1, the operation reference shall be

rejected and motor coast to a stop. To start the motor running, operation reference shall be firstly cancelled and then

input again.

Due to mechanical vibration or switch bouncing which may be caused by switch parts fault, operation may be not

inhibited although this parameter is set to 1. Thus great care shall be attached when using this function.

2-13

Reserved

2-14

Reserved

Содержание S900 Series























































































Результаты поиска

Содержание S900 Series

Отзывы:

Бренды по названию

Популярные бренды

Savch S900 Series, Руководство пользователя

Результаты поиска

Содержание S900 Series

Отзывы:

Бренды по названию

Популярные бренды