Savch S900 Series Скачать руководство пользователя страница 44

Страница: 44 / 86

2-06

External fault (EF) stop mode

Factory setting

d 1

Setting range

d 0: Reserved

d 1: External fault (EF) coast to stop

Description of action: When EF is detected by the system, a stop signal shall be sent and AC motor shall stop in the

mode of this parameter.

2-07

Reference loss detection(Terminal AVI)( stop mode)

Factory setting

d 2

Setting range

d 0: Deceleration stop

d 1: Coast to stop

d 2: Holding operation command after deceleration stop

Description of action: A stop signal shall be sent when frequency is set to AVI, parameter is set to d0 or d1 and

system has detected that AVI set frequency is 0, AC motor drive shall coast to a stop in accordance with this setting

at the same time; if this parameter is set to d2 and AVI set frequency is 0, motor stops by braking, but running signals

are reserved. Motor shall run continuously when AVI set frequency rise up again.

Notes: Operation key shall be unavailable when parameter is set to d0 or d1 and AVI input is 0

2-08

Reserved

Factory setting

d 0

2-09

Motor sound(Carrier frequency)

Factory setting

d 6.0

Setting range

d 2.0<->d 12.0kHz

Unit

0.1kHz

Load frequency of PWM output shall be set by this parameter.

Load frequency

Electromagnetic noise

Noise, spill current

Radiation

2kHz

Big

│

Small

│

Big

Small

│

Big

6kHz

12kHz

The above form suggests that carrier frequency outputted from PWM shall influence electromagnetic noise, radiation

as well as interference to the environment of motor; thus, decreasing the carrier frequency shall help the inverter to

decrease temperature rise if ambient noise exceeds noise of the motor; in case of high carrier frequency, although

operation noise shall be eliminated to a large degree, attention shall be paid to the interference and protection of the

machine.

Содержание S900 Series























































































Результаты поиска

Содержание S900 Series

Отзывы:

Бренды по названию

Популярные бренды

Savch S900 Series, Руководство пользователя

Результаты поиска

Содержание S900 Series

Отзывы:

Бренды по названию

Популярные бренды