ROBBE-Futaba FX-32 Скачать руководство пользователя страница 134

Страница: 134 / 180

134

<Model Menu (Airplane/Glider Functions)>

● S e l e c t t h e f u n c t i o n

name and return to the

preceding screen by

touching the

RTN

button

or pushing the

Home/Exit

button.

<SensorTouch™>

ELEVATOR

ELEVATOR 2

V-TAIL

ELEVATOR

ELEVATOR 2

AILVATOR

FLP 2

(Camber Flap)

FLP 1

(Camber Flap)

CAMB.FLP to ELE

[Corresponding model type]: Airplane/glider,

2 ai 1 flap or more

This mixing is used to correct changes (elevator

direction) generated when the camber flaps (speed

flaps) are used.

● The elevator servos up side/down side rate can be

adjusted. When the mixing direction is reversed

by the linkage, adjustments can be made by

changing the mixing rate polarity (+ or –).

● A mixing curve can be set.

● Mixing during flight can be turned ON/OFF by

setting a switch. (Always ON at [--] setting)

● The mixing rate can be fine-tuned by setting a VR.

● E l e v a t o r r a t e

adjustment

Setting method

● Move the cursor to the ACT/INH item and

touch the RTN button to switch to the data

input mode.

Turn the touch sensor to the left and touch

the RTN button. (ON is displayed.)

● When setting a switch, move the cursor to

the [--] item of the switch and touch the RTN

button to call the selection screen, and then

select the switch and set its ON direction.

(Always ON at "--" setting)

(For a description of the switch selection

method, see the description at the back of

this manual.

● Move the cursor to the elevator servos left

and right item and touch the RTN button to

switch to the data input mode. Adjust the

mixing rate with the touch sensor.

Touch the RTN button to end adjustment and

return to the cursol move mode.

*When the mixing direction is reversed by the linkage,

adjustments can be made by changing the mixing rate

polarity (+ or –).

● When setting a VR, move the cursor to the

Fine tuning "--" item and touch the RTN

button to call the selection screen, and then

select the VR. The VR operation mode can

be selected.

● A mixing curve can be set.
(For a description of the curve setting

method, see the description at the back of

this manual.)

● Overall adjustment by

Rate A and Rate B.

(Currently selected condition name)

● Select [CAMB.FLP to ELE] at the model menu and

call the setup screen shown below by touching

the RTN button.

● Mixing curve setting

*For a description of the curve setting method, see the

description at the back of this manual.

* T h e d i s p l a y s c r e e n i s a n

example. The actual screen

depends on the model type.

● Fine tuning VR setting

● Adjustment rate

● Operation mode

● Group/single mode

switching

(For more information,

refer to the description at

the back of this manual.)

Scrolling

● Moving cursor

● Selecting mode

● Adjusting value

● To next page

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды