ROBBE-Futaba FX-32 Скачать руководство пользователя страница 63

Страница: 63 / 180

<Functions of Linkage Menu>

FUNCTIONS OF LINKAGE MENU

The Linkage Menu is made up of functions

which perform model addition, model type

selection, frequency setting, end point setting, and

other model basic settings.

The functions which can be selected depend on

the model type. A typical menu screen is shown

below.

*The display screen is an example. The screen

depends on the model type.

Linkage Menu functions table

[SERVO MONITOR]: Displays the servo test and operation position

[MODEL SELECT]: Model addition, call, deletion, copy, model name setting

[MODEL TYPE]: Model type, wing type, swash type, etc. selection

[SYSTEM TYPE]: System mode selection, link of a transmitter and receiver, area mode selection

[FUNCTION]: Channel assignment of each function can be changed

[SUB-TRIM]: Adjusts the neutral position of each servo

[SERVO-REVERSE]: Servo direction reversal

[FAIL SAFE]: Fail safe function and battery fail safe function setting

[END POINT]: Servo basic rudder adjustment and limit setting

[THROTTLE CUT]: Stops the engine safely and easily (airplane and helicopter only)

[IDLE DOWN]: Lowers the idle speed of the engine (airplane and helicopter only)

[SWASH RING]: Limits the swash plate travel to within a fixedrange. (helicopter only)

[SWASH]: Swash AFR and linkage correction function (helicopter only)

[TIMER]: Timer setting

[T1-T6 SETTING]: Control step amount and mode selection of the digital trim

[MULTIPROP]: CH is extended by MPDX-1 of an option

[FUNCTION NAME]: Function name can be changed

[TELEMETRY]: Displays various data sent from the receiver

[SENSOR]: Various telemetry sensors setting

[TELE.SETTING]: Various telemetry sensors setting

[WARNING]: Mixing warning normal reset

[TRAINER]: Starts and sets the trainer system.

[DATA RESET]: Model memory set data reset (by item)

[COND. HOLD]: Condition hold function (helicopter only)

● Select [LINKAGE] at the home screen and call

the linkage menu shown below by touching

the RTN button.

● Use the touch sensor to select the function

you want to set and call the setup screen by

touching the RTN button.

To activate/deactivate Condition Hold:

(Helicopter type only)
1.Move the cursor to [COND. HOLD].
2.Set the throttle stick lower than

the 1/3 point and touch the RTN

button to activate/deactivate the

condition hold function.

*Refer to condition hold function details.

*Condition hold operation is displayed.

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

●Calling setup screen

Scrolling

● Moving cursor

● Push the

button

to call next page.

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды