ROBBE-Futaba FX-32 Скачать руководство пользователя страница 45

Страница: 45 / 180

<Functions of System Menu>

Operation switch setting method

1.Select [SWITCH] and call the setup screen

shown below by touching the RTN button.

2.Use the touch sensor to move the cursor to

the "SA-SJ" item corresponding to the switch

you want to change and touch the RTN

button to switch to the data input mode.

3. Change the "2Pos" or "3Pos" by turning the

touch sensor to the left or right. The display

blinks. It will decide, if the RTN button is

pushed. (To terminate mode change, turn

the touch sensor or push the S1 button.)

"3Pos": 3 position switch
"2Pos" : 2 position switch

Stick calibration method

*J3 and J4 correction is described below. J1 and J2

corrections are performed using the same procedure.

1.Select [CALIBRATION] and access the setup

screen shown below by touching the RTN

button.

2.Move the cursor to the J3-J4 button and

touch the RTN button.

3.Move the J3 or J4 sticks to the neutral position

and press the RTN button for one second.

4.Set the J3 and J4 sticks fully to the bottom

right and wait until the buzzer sounds.

5.Set the J3 and J4 sticks fully to the top left and

wait until the buzzer sounds.

6.The above completes the correction

operation. Operate and check if stick

correction was performed normally.

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды