ROBBE-Futaba FX-32 Скачать руководство пользователя страница 121

Страница: 121 / 180

121

<Model Menu (Airplane/Glider Functions)>

● Select the [MODEL MENU]

and return to the home

screen by touching the

RTN

button or pushing the

Home/Exit

button.

MODEL MENU (AIRPLANE/GLIDER FUNCTIONS)

The dedicated mixes, etc. usable when airplane

or glider model type is selected are displayed in

this Model Menu functions section. First use the

Model Type function of the Linkage Menu to

preset the model type, wing type, and tail type

matched to the fuselage used. Other settings reset

the data used in mixing function, etc.

These dedicated mixes can be set for each

flight condition, as required. When you want to

use the system by switching the settings for each

condition by switch or stick position, use the

Condition Select function to add flight conditions.

(Up to 8 conditions can be used)

Note: The FX-32 is designed so that the airplane and

glider model types can handle aircraft of the same

wing type.

The functions common to airplanes and gliders,

except some dedicated functions, are summarized

without regard to the model type.

The setting items are different, depending on the

number of servos, etc. according to the wing type

used. The setup screens in the instruction manual

are typical examples.

Model Menu functions list

AIL DIFFERENTIAL

This function adjusts the left and right ailerons.

Roll axis correction and fine tuning with a VR are

also possible. This is convenient when making

settings during flight.

[Airplane/glider, 2 ailerons or more]

FLAP SETTING

The flaps can be adjusted independently. For a

4 flaps model, the camber flaps can be mixed with

the brake flaps. [Airplane/glider, 2 flaps or more]

AIL to CAMBERFLP

This mix operates the camber flaps in

the aileron mode. It improves the operation

characteristic of the roll axis. [Airplane/glider, 2

ai 2 flaps or more]

AIL to BRAKEFLP

This mix operates the brake flaps in the aileron

mode. It improves the operation characteristic of

the roll axis. [Airplane/glider, 4 flaps or more]

AIL to RUD

This mix is used when you want to operate the

rudder at aileron operation. Banking at a shallow

bank angle is possible. [Airplane/glider, general]

AIRBRAKE to ELE

This mix is used to correct operation of the

airbrakes (spoilers) when landing. [Airplane/

glider, general]

(Model Menu screen example)
*The Model Menu screen depends on the model type.

This screen is for model type 4AIL+4FLP.

● Select the [MODEL] at the home screen

and call the model menu shown below by

touching the RTN button.

● Use the touch sensor to select the function

you want to set and call the setup screen by

touching the RTN button.

Scrolling

● Moving cursor

● To next page

<SensorTouch™>

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды