ROBBE-Futaba FX-32 Скачать руководство пользователя страница 91

Страница: 91 / 180

<Functions of Linkage Menu>

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

<SensorTouch™>

● Select [Rx-BATT.] in the TELEMETRY screen

and access the setup screen shown

below by touching the RTN button.

● Select [EXT BATT.] in the RECEIVER screen

and access the setup screen shown

below by touching the RTN button.

●A setup of the voltage on

which the alarm operates.

Scrolling

● Moving cursor

● EXT battery voltage

● The maximum and the minimum

when powering ON are shown.

It will be preset, if a cursor is

moved to this place and the

RTN button is pushed for 1

second.

● ↓The "down" arrow will

indicate that an alarm

will sound when the

voltage drops to below

the setting.

● ALARM is chosen from

BUZZER, VOICE, and

INHIBIT.

● The ON/OFF switch of SPEECH is

chosen.

Alarm set

1. Move the cursor to the ↓ALARM item, and

it chooses from BUZZER, VOICE, and INHIBIT,

and pushes RTN.

2. When not operating vibrator, it is

VIBRATOR"

to INHIBIT. TYPE1-3 will be chosen if it is made

to operate.

3. Move the cursor to the LIMIT [4.0V] item and

touch the RTN button to switch to the data

input mode.

4. Ajust the rate by scrolling the touch sensor.
Initial value: 4.0V
Adjustment range: 0.0V~100.0V

*When the RTN button is touched for one second, the rate is

reset to the initial value.

5. Touch the RTN button. (To terminate the input

and return to the original state, touch the

Home/Exit button.)

TYPE 1

TYPE 2

TYPE 3

"VIBRATOR" type

If the following types are selected, the transmitter

will vibrate during the warning.

TELEMETRY : RECEIVER [EXT BATT.]

Displaying data from the EXT battery

voltage port

The EXT-VOLT screen will display the data from

the EXT-battery output from the R7008SB receiver.

In order to use this function, it is necessary to

connect external voltage connector of the R7008SB

receiver to a CA-RVIN-700 (FUTM5551) or

SBS-01V to the battery you desire to measure the

voltage of.

You will be alerted by an alarm or vibration if

the voltage set by you is exceeded.

*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage will be received in

the FASSTest12CH mode.

*The FASSTest18CH mode will display all telemetry data.

*CA-RVIN-700 must be installed in the aircraft.

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды