ROBBE-Futaba FX-32 Скачать руководство пользователя страница 35

Страница: 35 / 180

<Basic Operation>

Screen lock

To prevent the data from being changed by erroneous touching of the touch sensor during flight,

a function which makes an touch sensor impossible temporarily.

How to lock

1. The home screen is displayed.
2. Press the S1 button for about 1 second.

"LOCK" is displayed and the touch sensor is

disabled.

How to unlock

1. Press the S1 button for about 1 second in the

touch sensor locked state. The touch sensor is

enabled again.

STARTUP LOCK

Auto Lock functions automatically when the

model changes or power is turned on.

*To temporarily allow access to the FX-32 programming

press and hold the S1 bitton for one second. Please note,

the Auto Lock function timer will resume immediately once

again.

AUTOMATIC LOCK

Auto Lock functions automatically when there is

no operation from the HOME screen display for a

chosen number of seconds.

*Two kinds of automatic locks can be

chosen by

[DISPLAY]

[SYSTEM MENU]

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды