ROBBE-Futaba FX-32, Инструкция по эксплуатации

Страница: 100 / 180

100 <Functions of Linkage Menu>
● Select the function name
and return to the Linkage
menu by touching the
RTN button or pushing the
Home/Exit button.
<SensorTouch™>
TELEMETRY : GPS [SPEED]
Displaying data from the speed
The speed screen displays and sets the speed data
from an SBS-01G (GPS sensor) sold separately.
The speed of the aircraft during flight can be
displayed. After flight, the maximum speed during
flight can be viewed. Because this speed is based on
position data from a GPS satellite, the ground speed
is displayed instead of air speed. Consequently,
with a head wind, the displayed speed decreases
and with a tail wind, the displayed speed increases.
*The GPS sensor is necessary, and is sold separately. Mount
and connect the sensor in accordance with the sensor
instruction manual.
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH mode can use all the telemetry functions.
*A GPS sensor must be installed in the aircraft.
●This indicates the receiving accuracy
from a GPS Satellite. When three bars
are displayed, the GPS is ready for use.
● Select [GPS] in the TELEMETRY screen and
access the setup screen shown below by
touching the RTN button.
Scrolling
● Moving cursor
● Speed
● ↓ A downward arrow
indicates the alarm
will sound when the
speed reaches below
your set value.
● ↑ An upward arrow
indicates the alarm
will sound when the
speed reaches above
your set value.
TYPE 1
TYPE 2
TYPE 3
"VIBRATOR" type
If the following types are selected, the
transmitter will vibrate during the warning.
●
Select [SPEED](small font display)
in the TEMPERATURE screen and
access the setup screen shown
below by touching the RTN button.
● The maximum and the minimum when
powering ON are shown. It will be preset,
if a cursor is moved to this place and the
RTN button is pushed for 1 second.
●The ON/OFF switch of
SPEECH is chosen.
● I t l i n k s w i t h t h e
"DISTACE" display.
●Pushing [PRESET] sets the current
aircraft position as the starting point.
Alarm setting when speed increases
1. Move the cursor to the ↑ALARM item, and
it chooses from BUZZER, VOICE, INHIBIT, and
pushes RTN.
2. When not operating vibrator, it is " VIBRATOR"
to INHIBIT. TYPE1-3 will be chosen if it is made
to operate.
3. Move the cursor to the LIMIT [km/h] item and
touch the RTN button to switch to the data
input mode.
4. Ajust the rate by scrolling the touch sensor.
Initial value: 200km/h
Adjustment range 0km/h~500km/h
(↑LIMIT ≧ ↓LIMIT)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
5. Touch the RTN button. (To terminate the input
and return to the original state, touch the
Home/Exit button.)
Alarm setting when speed decreases
1. Move the cursor to the ↓ALARM item, and
it chooses from BUZZER, VOICE, INHIBIT, and
pushes RTN.
2. When not operating vibrator, it is
"
VIBRATOR"
to INHIBIT. TYPE1-3 will be chosen if it is made
to operate.
3. Move the cursor to the LIMIT [km/h] item and
touch the RTN button to switch to the data
input mode.
4. Ajust the rate by scrolling the touch sensor.
Initial value: 0km/h
Adjustment range 0km/h~500km/h
(↑LIMIT
≧
↓LIMIT)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
5. Touch the RTN button. (To terminate the input
and return to the original state, touch the
Home/Exit button.)
*Speed alarm precaution
Since the GPS speed sensor displays the ground speed, it
cannot be used as a stall alarm. For example, an aircraft that
stalls at 50km/h will stall if the tailwind is 5km/h or greater
even through 55km/h is displayed by ground speed. In
addition, with an aircraft that will disintegrate in midflight at
400km/h at an over-speed alarm, when the headwind reaches
30km/h the airplane will disintegrate in midair due to over
speeding even at a ground speed of 370km/h.