ROBBE-Futaba FX-32, Инструкция по эксплуатации

Страница: 95 / 180

95 <Functions of Linkage Menu>
● Select the function name
and return to the Linkage
menu by touching the
RTN button or pushing the
Home/Exit button.
<SensorTouch™>
● Select [ALTITUDE] in the TELEMETRY screen and access the
setup screen shown below by touching the RTN button.
Scrolling
● Moving cursor
● ↓ A downward arrow
indicates the alarm
will sound when the
variomete reaches
below your set value.
● ↑ An upward arrow
indicates the alarm
will sound when the
variometer reaches
above your set value.
TYPE 1
TYPE 2
TYPE 3
"VIBRATOR" type
If the following types are selected, the
transmitter will vibrate during the warning.
●
Select [VARIOMETER](small font
display) in the TEMPERATURE screen
and access the setup screen
shown below by touching the RTN
button.
● The maximum and the minimum when
powering ON are shown. It will be preset, if
a cursor is moved to this place and the RTN
button is pushed for 1 second.
TELEMETRY : ALTITUDE [VARIOMETER]
Displaying data from the
variometer
VARIO is a screen which displays / sets up the
variometer information from an optional altitude
sensor or GPS sensor.
The variometer of the model which is flying can
be known.
If it becomes higher or lower than the setting an
alarm and/or vibration will alert you.
To ensure that the pilot is aware as to the model's
status, the FX-32 incorporates a different melody
for ascent and descent. Additionally, depending
upon the rate of climb or descent, the tones vary to
indicate whether or not the airplane is climbing or
descending at a rapid rate.
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH mode can use all the telemetry functions.
● Variometer
Alert set : Rise side
1. Move the cursor to the ↑ALARM item, and
it chooses from BUZZER, VOICE, INHIBIT, and
pushes RTN.
2. When not operating vibrator, it is " VIBRATOR"
to INHIBIT. TYPE1-3 will be chosen if it is made
to operate.
3. Move the cursor to the LIMIT [m/s] item and
touch the RTN button to switch to the data
input mode.
4. Ajust the rate by scrolling the touch sensor.
Initial value: +1m
Adjustment range-50m/s~+50m/s
(↑LIMIT ≧ ↓LIMIT)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
5. Touch the RTN button. (To terminate the input
and return to the original state, touch the
Home/Exit button.)
Alert set : Dive side
1. Move the cursor to the ↓ALARM item, and
it chooses from BUZZER, VOICE, INHIBIT, and
pushes RTN.
2. When not operating vibrator, it is " VIBRATOR"
to INHIBIT. TYPE1-3 will be chosen if it is made
to operate.
3. Move the cursor to the LIMIT [m/s] item and
touch the RTN button to switch to the data
input mode.
4. Ajust the rate by scrolling the touch sensor.
Initial value: -1m
Adjustment range-50m/s~+50m/s
(↑LIMIT ≧ ↓LIMIT)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
5. Touch the RTN button. (To terminate the input
and return to the original state, touch the
Home/Exit button.)
*An altitude sensor or GPS sensor must be installed in the aircraft.
●The ON/OFF switch of
SPEECH is chosen.
●If this is set to MODE1-4, a rise
and dive are told by a different
melody.
MODE1: Little rise/dive
→
Melody changes (sensitively)
MODE4: Big rise/dive
→
Melody changes (insensible)
. . .