ROBBE-Futaba FX-32 Скачать руководство пользователя страница 112

Страница: 112 / 180

112

<Model Menu (Common Functions)>

● Select the [MODEL MENU]

and return to the home

screen by touching the

RTN

button or pushing the

Home/Exit

button.

MODEL MENU (COMMON FUNCTIONS)

This section describes the AFR, program mixing,

and other functions common to all model types.

Before setting the model data, use the Model

Type function of the Linkage Menu to select the

model type matched to the fuselage. When another

model type is selected thereafter, the AFR, program

mixing, and other setting data are reset.

The functions in the Model Menu can be set for

each flight condition. When you want to use the

system by switching the settings for each condition

by switch, stick position, etc., use the Condition

Select function to add flight conditions. (Up to 8

conditions can be used)

Note: The FX-32 is designed so that the airplane

and glider (including EP glider) model types are

compatible with aircraft of similar type wings.

This section outlines the relationship between the

functions common to airplanes and gliders, except

some dedicated functions, and model type.

The setting items depend on the number of servos

and other differences according to the wing type

used, but reread them. The setup screens in the

instruction manual are typical examples.

(Model Menu screen example)
*The Model Menu screen depends on the model type.

This screen is for model type 4AIL+4FLP.

Model Menu functions (Common) list

●SERVO MONITOR

Servo test and servo position display (For a

description of its functions, see the Linkage Menu

section.)

●COND.SELECT

Flight conditions addition, deletion, copy,

condition renaming, and condition delay can be set.

●AFR

Sets the angle and curve of all the operation

functions.

●DUAL RATE

A D/R curve which can be switched with a switch,

etc. can also be added.

●PROG. MIX

Program mixing which can be freely customized.

Up to 10 mixes can be used for each condition.

● Select the [MODEL] at the home screen

and call the model menu shown below by

touching the RTN button.

● Use the touch sensor to select the function

you want to set and call the setup screen by

touching the RTN button.

Scrolling

● Moving cursor

● To next page

<SensorTouch™>

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды