ROBBE-Futaba FX-32 Скачать руководство пользователя страница 126

Страница: 126 / 180

126

<Model Menu (Airplane/Glider Functions)>

● S e l e c t t h e f u n c t i o n

name and return to the

preceding screen by

touching the

RTN

button

or pushing the

Home/Exit

button.

<SensorTouch™>

AIL 3

(Chip Aileron)

AIL 4

(Chip Aileron)

AIL1

(Main Aileron)

AIL 2

(Main Aileron)

FLP 3

(Brake Flap)

FLP 4

(Brake Flap)

AIL to BRAKEFLP

[Corresponding model type]: Airplane/glider, 4 flaps or more

This mix operates the brake flaps (FLP3/4)

in the aileron mode. When the aileron stick

is manipulated, the aileron and brake flaps

perform the aileron operation simultaneously

and the operation characteristic of the roll axis is

improved.

● The aileron left and right mixing rates can be

adjusted for each flap servo.

● A mixing curve can be set.

● Mixing during flight can be turned ON/OFF by

setting a switch. (Always ON at [--] setting)

● Linking can be set: Link this mix to other mixes.

●Setting method

● Move the cursor to the ACT/INH item and

touch the RTN button to switch to the data

input mode.

Turn the touch sensor to the left and touch

the RTN button. (ON is displayed.)

● When setting a switch, move the cursor to

the [--] item of the switch and touch the RTN

button to call the selection screen, and then

select the switch and set its ON direction.

(Always ON at "--" setting)

(For a description of the switch selection

method, see the description at the back of

this manual.)

● Move the cursor to the left or right button of

each flap servo and touch the RTN button to

switch to the data input mode.

Adjust the mixing rate with the touch sensor.
Touch the RTN button to end adjustment and

return to the cursol move mode.

*When the mixing direction is reversed by the linkage,

adjustments can be made by reversing the mixing rate

polarity (+ or -).

● A mixing curve can be set.
(For a description of the curve setting

method, see the description at the back of

this manual.)

● To set linking, move the cursor to the Link item

and touch the RTN button to switch to the

data input mode.

Set it to ON and touch the RTN button.

● Mixing curve setting

*For a description of the curve setting method, see the

description at the back of this manual.

● Adjustment of each flap

servo

● L e f t / r i g h t o v e r a l l

adjustment at Rate A

and Rate B

(Currently selected condition name)

● Select [AIL to BRAKEFLP] at the model

menu and call the setup screen shown

below by touching the RTN button.

● Group/single mode

switching

(For more information, refer to

the description at the back of

this manual.)

*The display screen is an example. The actual

screen depends on the model type.

Scrolling

● Moving cursor

● Selecting mode

● Adjusting value

● To next page

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды