ROBBE-Futaba FX-32 Скачать руководство пользователя страница 48

Страница: 48 / 180

<Functions of System Menu>

● Select the function name

and return to the System

menu by touching the

RTN button or pushing the

Home/Exit button.

<SensorTouch™>

Procedure for changing S.BUS/S.BUS2 servo setting

1. Select [S.BUS Servo] of the System Menu.
2. Wire the servo as shown in the figure above.
3. Press [READ]. The ID and current setting of that servo

are displayed.

4. When multiple servos are connected change [INH]

at the right side of the ID number on the screen to

[ACT] and enter the ID of the servo you want to set.

5. Set each item. (Please see the next page.)
6. Press [WRITE]. The settings are changed.

S.BUS Servo

S.BUS/S.BUS2 servo setting

An S.BUS/S.BUS2 servo can memorize

the channel and various settings itself. Servo

setting can be performed on the FX-32 screen

by wiring the servo as shown in the figure.

● Call the following setting screen by pressing the

[S.BUS Servo] button in the System Menu.

●Servo ID number

Individual ID numbers are memorized for your

S.BUS servos in your FX-32. When a servo is

used (as shown at the right), the servo ID number is

automatically read by the transmitter.

If you use multiple S.BUS servos and do not want

to change the settings on all that are mounted in a

fuselage, only the desired servo in the group can be

set by entering the ID of that specific servo.

* With S.BUS/S.BUS2 servos of use, there are a function which can

be used, and an impossible function and a display screen changes.

(Only the function which can be used by a servo is displayed.)

* After reading completion, with connection of the above

figure, if a stick is moved, the test of operation of the

servo can be operated and carried out.

S.BUS/S.BUS2 servo

FX-32

*It is not necessary to carry out multiple connection of

the battery like a T18MZ/T14SG.

(It will damage, if it connects.)

Scrolling

● Moving cursor

● Push the S1 button to

call next page.

*When you connect to a transmitter many servos which

consume many current, please use "Another power

supply HUB". And electric power is supplied to a servo

with another power supply.

Battery

Hub

（Another power supply）

Hub

（Another power supply）

S.BUS Servo

●When separate power supply used

When a large number of servos are used or

when high current servos are used (Current

over 1A), the servos can be driven by a

separate power supply by using a separate

Power Supply 3-way hub.

Note:

If a battery over 5V i used, you have to

remove the red cord from the plug (as

shown in the draw). If not the transmitter

can be destroyed!

Used when using a separate

power supply battery.

Switch

Green

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды