ROBBE-Futaba FX-32, Инструкция по эксплуатации

Страница: 93 / 180

93 <Functions of Linkage Menu>
● Select the function name
and return to the Linkage
menu by touching the
RTN button or pushing the
Home/Exit button.
<SensorTouch™>
● T h e m a x i m u m a n d t h e
minimum when powering ON
are shown. It will be preset, if
a cursor is moved to this place
and the RTN button is pushed
for 1 second.
●A setup of the revolution on
which the alarm operates.
TELEMETRY : RPM SENSOR
Displaying data from the RPM
RPM sensor is a screen which displays / sets up
the rotation information from an optional RPM
sensor.
The rotation of the model (engine, motor, etc.)
which is flying can be shown.
If it becomes higher or lower than the setting an
alarm and/or vibration will alert you.
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH mode can use all the telemetry functions.
● Select [RPM sensor] in the TELEMETRY
screen and access the setup screen
shown below by touching the RTN
button.
Scrolling
● Moving cursor
● RPM
●"MAGNET" or "OPTICS" is
set according to the
sensor you use.
SBS-01RM : MAGNET
SBS-01RO : OPTICS
● ↓A downward arrow
indicates that the
a l a r m w i l l s o u n d
when the RPM falls
below the set value.
● ↑An upward arrow
indicates that the
a l a r m w i l l s o u n d
when the RPM rises
above the set value.
Alarm set : Over rotations
1. Move the cursor to the ↑ALARM item, and
it chooses from BUZZER, VOICE, INHIBIT, and
pushes RTN.
2. When not operating vibrator, it is " VIBRATOR"
to INHIBIT. TYPE1-3 will be chosen if it is made
to operate.
3. Move the cursor to the LIMIT [2,000rpm] item
and touch the RTN button to switch to the
data input mode.
4. Ajust the rate by scrolling the touch sensor.
Initial value: 2,000rpm
Adjustment range: 0rpm~150,000rpm
(↑LIMIT
≧
↓LIMIT)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
5. Touch the RTN button. (To terminate the input
and return to the original state, touch the
Home/Exit button.)
Alarm set : Under rotations
1. Move the cursor to the ↓ALARM item, and
it chooses from BUZZER, VOICE, INHIBIT, and
pushes RTN.
2. When not operating vibrator, it is " VIBRATOR"
to INHIBIT. TYPE1-3 will be chosen if it is made
to operate.
3. Move the cursor to the LIMIT [0rpm] item and
touch the RTN button to switch to the data
input mode.
4. Ajust the rate by scrolling the touch sensor.
Initial value: 0rpm
Adjustment range: 0rpm~150,000rpm
(↑LIMIT
≧
↓LIMIT)
*When the RTN button is touched for one second, the rate is
reset to the initial value.
5. Touch the RTN button. (To terminate the input
and return to the original state, touch the
Home/Exit button.)
● In "MAGNET", the gear ratio of
your engine (motor) you are
using is entered.
● In "OPTICS", the number of
blades of the propeller ( r o t o r
) your model is entered.
*A RPM sensor must be installed in the aircraft.
TYPE 1
TYPE 2
TYPE 3
"VIBRATOR" type
If the following types are selected, the transmitter
will vibrate during the warning.
●
Select [ROTATION](small font
display) in the RPM sensor
screen and access the setup
s c r e e n s h o w n b e l o w b y
touching the RTN button.
● The ON/OFF switch
of SPEECH is chosen.