ROBBE-Futaba FX-32 Скачать руководство пользователя страница 115

Страница: 115 / 180

115

<Model Menu (Common Functions)>

● S e l e c t t h e f u n c t i o n

name and return to the

preceding screen by

touching the

RTN

button

or pushing the

Home/Exit

button.

<SensorTouch™>

AFR

The angle and curve of each operation function can be set. [All model types]

AFR function is used to adjust the throw and

operation curve of the stick, lever, and switch

functions for each flight condition. This is normally

used after End Point has defined the maximum

throw. When mixing is applied from one channel

to another channel, both channels can be adjusted

at the same time by adjusting the operation rate

through the AFR function.

● Operation curve adjustment: Three types

of curves (EXP1, EXP2, and POINT) can be

selected. A maximum 17 points curve can be

used for the point curve type. (Initial setting:

9 points) The number of points can also be

increased and decreased and curves from

complex curves to simple curves can be

used.

● Operation speed adjustment: The operation

speed of each function when the function

is operated (including at flight condition

switching) can be adjusted. The function

operates smoothly at a constant speed

corresponding to the set speed.

(Currently selected condition name)

(Number of D/R curves set at the currently

selected condition)

●Servo speed setting

(For a description of the setting

method, see the description at

the back of this manual.)

●Group/single mode switch (GROUP/SINGLEl)

(For more information, see the description at the back

of this manual.)

●Operation curve setting

(For a description of the setting method, see the

description at the back of this manual.)

● Select [AFR] at the model menu and call the setup

screen shown below by touching the RTN button.

Function selection method

1. Use the touch sensor to move the cursor to [FUNC.] and touch the

RTN button to switch to the data input mode.

2. Select the desired function by scrolling the touch sensor to the left

or right, touch the RTN button.

*The setting mode (group [GROUP]/single [SNGLE] mode) can be switched (For more

information, see the description at the back of this manual.)

[AFR/D/R]: Displays the currently

selected rate (AFR/D/R).

●Function selection

Scrolling

● Moving cursor

● Selecting mode

● Adjusting value

● To next page

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды