ROBBE-Futaba FX-32 Скачать руководство пользователя страница 29

Страница: 29 / 180

<Before Use>

S.BUS/S.BUS2 device setting

S.BUS/S.BUS2 servos or a telemetry sensor can be connected directly to the FX-32. Channel setting and

other data can be entered for the S.BUS/S.BUS2 servos or sensors.

(S.BUS/S.BUS2 servo)

S.BUS/S.BUS2

device

(Telemetry sensor)

FX-32

1. Connect the S.BUS device you want to set with

as shown in the figure.

2. Turn on the transmitter power.
3. Call the setup screen.

Servo: System Menu

→

S.BUS servo

Sensor: Linkage Menu

→

Sensor

4. Perform setting in accordance with each screen.

5. This sets the channel and other data for each

S.BUS servo, or telemetry device to be used with

the S.BUS device or receiver.

*It is not necessary to carry out multiple

connection of the battery like a T18MZ/

T14SG.

(It will damage, if it connects.)

*When you connect to a transmitter many servos

which consume many current, please use

"Another power supply HUB".

And electric power is supplied to a servo with

another power supply.

Battery

Hub

（Another power supply）

Hub

（Another power supply）

S.BUS Servo

●When separate power supply used

When a large number of servos are used or

when high current servos are used (Current

over 1A), the servos can be driven by a

separate power supply by using a separate

Power Supply 3-way hub.

Note:

If a battery over 5V i used, you have to

remove the red cord from the plug (as

shown in the draw). If not the transmitter

can be destroyed!

Used when using a separate

power supply battery.

Switch

Green

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Бренды по названию

Популярные бренды