ROBBE-Futaba FX-32 Скачать руководство пользователя страница 155

Страница: 155 / 180

155

<Functions of Model Menu (Helicopter Functions)>

Normal Curve

Idle-up 1 Curve

Idle-up 2 Curve

●Throttle Curve (Example)

The curves shown below are created by using

the point curve type and inputting the data of the

5 points 0% (low side), 25%, 50% (center), 75%,

100% (high) side at each condition. They are

created by reducing the number points of the line

to 5. When actually creating a curve, enter the data

specified per the aircraft (or the reference value).

*For a description of the curve creation method, see the

description at the back of this manual.

Curve setting examples

Throttle Hover trim

The Throttle Hover trim setup screen can be called from the THR Curve setup screen.

The Throttle Hover function trims the throttle

near the hovering point. Normally, use it with

hovering conditions. Changes in rotor speed

accompanying changes in the temperature,

humidity, and other flight conditions can be

trimmed. Adjust the throttle so that rotor rotation is

most stable. More delicate trimming is also possible

by using this function along with the Hover Pitch

function.

Setting method

● When using the hovering (normal) condition

only, switch the group mode to the single

mode (initial setting) and make the settings.

●  Set the function to ACT ([ON]).
●  Select the adjustment knob.
  Selection example: RD
●  The  trim  operation  mode  (Mode:  CTRM/

NORM) can be selected.

CTRM mode:

Maximum rate of change

near center by center trim operation

(recommended)

NORM mode:

Normal trim (horizontal

movement trim) operation.

● Trim adjustment range (Range) setting
When the value is made small, trim acts only

near the center.

● The trim rate can be adjusted and the

operation direction can be set.

●Sets the dial used.

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды