ROBBE-Futaba FX-32 Скачать руководство пользователя страница 141

Страница: 141 / 180

141

<Model Menu (Airplane/Glider Functions)>

● S e l e c t t h e f u n c t i o n

name and return to the

preceding screen by

touching the

RTN

button

or pushing the

Home/Exit

button.

<SensorTouch™>

GYRO

[Corresponding model type]: Airplane/glider, general

This function is used when a GYA Series gyro

is used to stabilize the aircraft's attitude. The

sensitivity and operation mode (Normal mode/GY

mode) can be switched with a switch.

● Three rates (Rate 1/Rate 2/Rate 3) can be

switched.

● Up to 3 axes (Gyro/Gyro 2/Gyro 3) can be

simultaneously controlled.

*Initial setting does not assign a sensitivity channel. Use the

Function menu of the Linkage Menu to assign the sensitivity

channel (Gyro/Gyro2/Gyro3) used to a vacant channel

beforehand.

Set [Control] and [Trim] other than Function to [--].

● The operation mode (AVCS/NOR) and sensitivity of

the 3 axes Gyro/Gyro2/Gyro3 can be set.

● Group/single mode

switching

(For more information, see the

description at the back of this

manual.)

● Three rates (Rate 1/Rate 2/Rate 3) can be used.
Move the cursor to the [RATE] item and touch the RTN button to switch

to the data input mode. Adjust the rate by scrolling the touch sensor.

● When using this function, move the cursor to the [ACT] item and touch

the RTN button to switch to the data input mode. Turn the touch sensor

to the left and touch the RTN button.

● When a Futaba GYA gyro is used, when [GY] type is selected, the

sensitivity set value is directly read in both the AVCS and NORM modes.

● When setting a switch, move the cursor to the SWITCH item and press

the EDIT button to call the selection screen, and then select the switch

and set its ON direction.

(For a description of the switch selection method, see the description at

the end of this manual.)

(Currently selected condition name)

● Select [GYRO] at the model menu and

call the setup screen shown below by

touching the RTN button.

Scrolling

● Moving cursor

● Selecting mode

● Adjusting value

● To next page

Содержание FX-32





















































































































































































Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды

ROBBE-Futaba FX-32, Инструкция по эксплуатации

Результаты поиска

Содержание FX-32

Отзывы:

Похожие инструкции для FX-32

Бренды по названию

Популярные бренды