manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 363 of 760

11.3.5

Number of Bus Cycle States and 

D

D

D

DR

R

R

RE

EE

EQ

Q

Q

Q

 Pin Sampling Timing

Number of Bus Cycle States: When the DMAC is the bus master, the number of bus cycle states
is controlled by the bus state controller (BSC) in the same way as when the CPU is the bus master.
For details, see section 10, Bus State Controller (BSC).

D

D

D

DR

R

R

RE

EE

EQ

Q

Q

Q

 Pin Sampling Timing: In external request mode, the 

DREQ

 pin is sampled by clock pulse

(CKIO) falling edge or low level detection. When 

DREQ

 input is detected, a DMAC bus cycle is

generated and DMA transfer performed, at the earliest, three states later.

The second and subsequent 

DREQ

 sampling operations are started two cycles after the first

sample.

Operation

•

 

Cycle-Steal Mode

In cycle-steal mode, the 

DREQ

 sampling timing is the same regardless of whether level or

edge detection is used.

For example, in figure 11.15 (cycle-steal mode, level input), DMAC transfer begins, at the
earliest, three cycles after the first sampling is performed. The second sampling is started two
cycles after the first. If 

DREQ

 is not detected at this time, sampling is performed in each

subsequent cycle.

Thus, 

DREQ

 sampling is performed one step in advance. The third sampling operation is not

performed until the idle cycle following the end of the first DMA transfer.

The above conditions are the same whatever the number of CPU transfer cycles, as shown in
figure 11.16. The above conditions are also the same whatever the number of DMA transfer
cycles, as shown in figure 11.17.

DACK is output in a read in the example in figure 11.15, and in a write in the example in
figure 11.16. In both cases, DACK is output for the same duration as 

CSn

.

Figure 11.18 shows an example in which sampling is executed in all subsequent cycles when

DREQ

 cannot be detected.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

TC-Helicon PERFORM-VK Quick Start Manual preview
PERFORM-VK
Бренд: TC-Helicon Страницы: 2
SMART MOD IIC Installation And Service Manual preview
MOD IIC
Бренд: SMART Страницы: 15
Roland MSL-15 Owner'S Manual preview
MSL-15
Бренд: Roland Страницы: 12
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Бренд: Tandberg Data Страницы: 28
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Бренд: Eaton Страницы: 114
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Бренд: UNA AUTOMATION Страницы: 20
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Бренд: C-Com Страницы: 148
Advantech ARK-1380 User Manual preview
ARK-1380
Бренд: Advantech Страницы: 50
Alula RE930R LTE M1 Install Manual preview
RE930R LTE M1
Бренд: Alula Страницы: 4
Laser UDC CARD User Manual preview
UDC CARD
Бренд: Laser Страницы: 4
Lanner ECA-4027 User Manual preview
ECA-4027
Бренд: Lanner Страницы: 99
IBM 09N4076 User Manual preview
09N4076
Бренд: IBM Страницы: 78
Lattice Semiconductor mVision AR0234 User Manual preview
mVision AR0234
Бренд: Lattice Semiconductor Страницы: 25
Paradyne JetFusion 2004 User Manual preview
JetFusion 2004
Бренд: Paradyne Страницы: 216
G&D ControlCenter-IP 2.0 Installation Manual preview
ControlCenter-IP 2.0
Бренд: G&D Страницы: 60
Hama 62732 Operating Instructions Manual preview
62732
Бренд: Hama Страницы: 34
Acer AN1600 F1 Specifications preview
AN1600 F1
Бренд: Acer Страницы: 22
Acer Altos S200F User Manual preview
Altos S200F
Бренд: Acer Страницы: 58

Бренды по названию

Популярные бренды

Загрузить еще бренды