manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 563 of 760

17.3

Operation Description

The IrDA module can perform infrared communication conforming to IrDA 1.0 by connecting
infrared transmit/receive units. The serial communication interface unit includes a 16-stage FIFO
buffer in the transmit unit and the receive unit, allowing CPU overhead to be reduced and
continuous high-speed communication to be performed.  This module also supports DMAC data
transfer.  The IrDA module differs from the SCIF described in section 16, Serial Communication
Interface with FIFO (SCIF) in that it does not include modem control signals RTS and CTS.

Refer to section 16.3, Operation, for SCIF mode operation.

17.3.1

Overview

The IrDA module modifies TxD/RxD transmit/receive data waveforms to satisfy the IrDA 1.0
specification for infrared communication.

In the IrDA 1.0 specification, communication is first performed at a speed of 9600 bps, and the
communication speed is changed.  However, the communication rate cannot be automatically
changed in this module, so the communication speed should be confirmed, and the appropriate
speed set for this module by software.

Note:

In IrDA mode, reception cannot be performed when the TE bit in the serial control register
(SCSCR) is set to 1 (enabling transmission).  When performing reception, clear the TE bit
in SCSCR to 0.
As the SH7709S's RxD1 pin is active-high in IrDA mode, a (Schmidt) inverter must be
inserted when connecting an active-low IrDA module.
The RxD1 pin is active-low in SCIF mode.

17.3.2

Transmitting

In the case of a serial output signal (UART frame) from the SCIF, its waveforms are modified and
the signal is converted into the IR frame serial output signal by the IrDA module, as shown in
figure 17.5.

When serial data is 0, a pulse of 3/16 the IR frame bit width is generated and output. When serial
data is 1, no pulse is output.

An infrared LED is driven by this signal demodulated to 3/16 width.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

IBM System x3630 M4 Manual preview
System x3630 M4
Бренд: IBM Страницы: 7
Belkin F5D9001 Series Manual preview
F5D9001 Series
Бренд: Belkin Страницы: 72
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Бренд: ekwb Страницы: 2
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Бренд: LGC wireless Страницы: 154
MF DIGITAL DIRECTOR PRO series Operator'S Manual preview
DIRECTOR PRO series
Бренд: MF DIGITAL Страницы: 79
Renesas H8/3864 Series User Manual preview
H8/3864 Series
Бренд: Renesas Страницы: 20
Xantech CC12 Installation Instructions preview
CC12
Бренд: Xantech Страницы: 4
ZALMAN CNPS 4X User Manual preview
CNPS 4X
Бренд: ZALMAN Страницы: 16
Black Box Secure Site Manager 16 Quick Start Manual preview
Secure Site Manager 16
Бренд: Black Box Страницы: 16
S&P Turbo-3000 Operating Instructions preview
Turbo-3000
Бренд: S&P Страницы: 3
ProSoft MVI46-PDPS User Manual preview
MVI46-PDPS
Бренд: ProSoft Страницы: 53
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Бренд: IEI Technology Страницы: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Бренд: RadioSPECTRAL Страницы: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Бренд: ZALMAN Страницы: 9
Matrix Switch Corporation MSC-CP16X4E Product Manual preview
MSC-CP16X4E
Бренд: Matrix Switch Corporation Страницы: 48
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Бренд: Grundfos Страницы: 40
Advantech EPC-R6410 User Manual preview
EPC-R6410
Бренд: Advantech Страницы: 70
Hanwha Techwin Wisenet XRN-6410DB4 User Manual preview
Wisenet XRN-6410DB4
Бренд: Hanwha Techwin Страницы: 118

Бренды по названию

Популярные бренды

Загрузить еще бренды