manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page xxiv of xliv

12.3

TMU Operation ................................................................................................................. 400
12.3.1 General Operation ................................................................................................ 400
12.3.2 Input Capture Function......................................................................................... 403

12.4

Interrupts ........................................................................................................................... 404
12.4.1 Status Flag Setting Timing ................................................................................... 404
12.4.2 Status Flag Clearing Timing................................................................................. 405
12.4.3 Interrupt Sources and Priorities ............................................................................ 405

12.5

Usage Notes....................................................................................................................... 406
12.5.1 Writing to Registers.............................................................................................. 406
12.5.2 Reading Registers................................................................................................. 406

Section 13   Realtime Clock (RTC)

.................................................................................. 407

13.1

Overview ........................................................................................................................... 407
13.1.1 Features ................................................................................................................ 407
13.1.2 Block Diagram ..................................................................................................... 408
13.1.3 Pin Configuration ................................................................................................. 409
13.1.4 RTC Register Configuration................................................................................. 410

13.2

RTC Registers ................................................................................................................... 411
13.2.1 64-Hz Counter (R64CNT).................................................................................... 411
13.2.2 Second Counter (RSECCNT)............................................................................... 411
13.2.3 Minute Counter (RMINCNT) .............................................................................. 412
13.2.4 Hour Counter (RHRCNT) .................................................................................... 412
13.2.5 Day of Week Counter (RWKCNT) ...................................................................... 413
13.2.6 Date Counter (RDAYCNT).................................................................................. 414
13.2.7 Month Counter (RMONCNT).............................................................................. 414
13.2.8 Year Counter (RYRCNT) .................................................................................... 415
13.2.9 Second Alarm Register (RSECAR)...................................................................... 415
13.2.10 Minute Alarm Register (RMINAR) ..................................................................... 416
13.2.11 Hour Alarm Register (RHRAR) ........................................................................... 416
13.2.12 Day of Week Alarm Register (RWKAR) ............................................................. 417
13.2.13 Date Alarm Register (RDAYAR) ........................................................................ 418
13.2.14 Month Alarm Register (RMONAR)..................................................................... 418
13.2.15 RTC Control Register 1 (RCR1) .......................................................................... 419
13.2.16 RTC Control Register 2 (RCR2) .......................................................................... 420

13.3

RTC Operation .................................................................................................................. 422
13.3.1 Initial Settings of Registers after Power-On ......................................................... 422
13.3.2 Setting the Time ................................................................................................... 422
13.3.3 Reading the Time ................................................................................................. 423
13.3.4 Alarm Function .................................................................................................... 424
13.3.5 Crystal Oscillator Circuit...................................................................................... 425

13.4

Usage Notes....................................................................................................................... 426
13.4.1 Register Writing during RTC Count .................................................................... 426
13.4.2 Use of Realtime Clock (RTC) Periodic Interrupts ............................................... 426

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Paradyne 4300 Installation Instructions Manual preview
4300
Бренд: Paradyne Страницы: 22
Yamaha EMP100 Supplementary Manual preview
EMP100
Бренд: Yamaha Страницы: 4
Xinje XG Series User Manual preview
XG Series
Бренд: Xinje Страницы: 76
XIA Pixie-4 Express Software Manual preview
Pixie-4 Express
Бренд: XIA Страницы: 17
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Бренд: mikroElektronika Страницы: 3
Opengear IMG4216-25 Quick Start Manual preview
IMG4216-25
Бренд: Opengear Страницы: 2
Dialogic EDP-10 Quick Install Manual preview
EDP-10
Бренд: Dialogic Страницы: 2
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Бренд: Hanwha Techwin Страницы: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Бренд: ZALMAN Страницы: 9
A4Tech RG-71M User Manual preview
RG-71M
Бренд: A4Tech Страницы: 7
Glacier G2080TiFE Installation Manual preview
G2080TiFE
Бренд: Glacier Страницы: 2
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Бренд: Z3 Technology Страницы: 67
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Бренд: axing Страницы: 4
IEI Technology PulM-1G4T-I211 Quick Installation Manual preview
PulM-1G4T-I211
Бренд: IEI Technology Страницы: 2
Xantech CC62 Installation Instructions preview
CC62
Бренд: Xantech Страницы: 5
Idis DR-2308P Quick Manual preview
DR-2308P
Бренд: Idis Страницы: 18
TANDBERG 240LTO Quick Start Manual preview
240LTO
Бренд: TANDBERG Страницы: 2
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Бренд: A.E.B. Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды