manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 92 of 760

4.3

Register Descriptions

There are four registers related to exception handling. These are peripheral module registers, and
therefore reside in area P4. They can be accessed by specifying the address in privileged mode
only.

1. The exception event register (EXPEVT) resides at address H'FFFFFFD4, and contains a 12-bit

exception code. The exception code set in EXPEVT is that for a reset or general exception
event. The exception code is set automatically by hardware when an exception occurs.
EXPEVT can also be modified by software.

2. The interrupt event register (INTEVT) resides at address H'FFFFFFD8, and contains a 12-bit

interrupt exception code or a code indicating the interrupt priority. Which is set when an
interrupt occurs depends on the interrupt source (see tables 6.4 and 6.5). The exception code or
interrupt priority code is set automatically by hardware when an exception occurs. INTEVT
can also be modified by software.

3. Interrupt event register 2 (INTEVT2) resides at address H'04000000, and contains a 12-bit

exception code. The exception code set in INTEVT2 is that for an interrupt request. The
exception code is set automatically by hardware when an exception occurs.

4. The TRAPA exception register (TRA) resides at address H'FFFFFFD0, and contains 8-bit

immediate data (imm) for the TRAPA instruction. TRA is set automatically by hardware when
a TRAPA instruction is executed. TRA can also be modified by software.

The bit configurations of the EXPEVT, INTEVT, INTEVT2, and TRA registers are shown in
figure 4.3.

31

0

0 Exception code

imm

00

11

0

EXPEVT, INTEVT, and INTEVT2 registers

8-bit immediate data in TRAPA instruction

imm:

0:

Reserved bits, always read as 0

31

0

0

9

2

0

TRA register

Figure 4.3   Bit Configurations of EXPEVT, INTEVT, INTEVT2, and TRA Registers

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

GE MDS 4710M Setup Manual preview
MDS 4710M
Бренд: GE Страницы: 6
CAME Z Series Manual preview
Z Series
Бренд: CAME Страницы: 4
Magnat Audio MC 200 Faq preview
MC 200
Бренд: Magnat Audio Страницы: 2
Baicells Nova430i Quick Manual preview
Nova430i
Бренд: Baicells Страницы: 8
A2B Electronics ECX-200 Installation Manual preview
ECX-200
Бренд: A2B Electronics Страницы: 24
ZALMAN CNPS6000-Al User Manual preview
CNPS6000-Al
Бренд: ZALMAN Страницы: 6
Bitspower BPTA-CPUMS-V2-SKA Instruction Manual preview
BPTA-CPUMS-V2-SKA
Бренд: Bitspower Страницы: 6
Alarm NX-208E Installation Manual preview
NX-208E
Бренд: Alarm Страницы: 5
Primera Disc Publisher XR Installation Instructions preview
Disc Publisher XR
Бренд: Primera Страницы: 2
IBM EtherLink XL User Manual preview
EtherLink XL
Бренд: IBM Страницы: 72
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Бренд: Xantech Страницы: 16
NUROTRON CS-10A Operation Manual preview
CS-10A
Бренд: NUROTRON Страницы: 16
ICP DAS USA WF-2572M User Manual preview
WF-2572M
Бренд: ICP DAS USA Страницы: 26
Jäger ADwin-light-16 Manual preview
ADwin-light-16
Бренд: Jäger Страницы: 54
Tachosys digiDL-B Administration Manual preview
digiDL-B
Бренд: Tachosys Страницы: 15
ADTRAN JOBAID T200 IDSL Quick Start Manual preview
JOBAID T200 IDSL
Бренд: ADTRAN Страницы: 2
Crestron CAEN-CK-7x1 Quick Start Manual preview
CAEN-CK-7x1
Бренд: Crestron Страницы: 2
Crestron QM-IEM Installation Manual preview
QM-IEM
Бренд: Crestron Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды