manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 509 of 760

15.4.2

Retransmission (Receive and Transmit Modes)

Retransmission when SCI is in Receive Mode: Figure 15.9 shows the retransmission operation
in the SCI receive mode.

1. When the received parity bit is checked and an error is found, the PER bit in SCSSR is

automatically set to 1. If the RIE bit in SCSCR is enabled at this time, an ERI interrupt is
requested. Be sure to clear the PER bit before the next parity bit is sampled.

2. The RDRF bit in SCSSR is not set in the frame that caused the error.

3. When the received parity bit is checked and no error is found, the PER bit in SCSSR is not set.

4. When the received parity bit is checked and no error is found, reception is considered to have

been completed normally and the RDRF bit in SCSSR is automatically set to 1. If the RIE bit
in SCSCR is enabled at this time, an RXI interrupt is requested.

5. When a normal frame is received, the pin maintains a three-state state when it transmits the

error signal.

D0

Ds

D2

D1

D4

D3

D6

D5

Dp DE

D7

D0

Ds

D2

D1

D4

D3

D6

D5

Dp

(DE)

D7

D0

Ds

D2

D1

D4

D3

nth transfer frame

RDRF

PER

2

1

4

5

3

Retransmitted frame

Transfer frame n + 1

Figure 15.9   Retransmission in SCI Receive Mode

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Бренд: D-Link Страницы: 12
Baicells Nova430i Quick Manual preview
Nova430i
Бренд: Baicells Страницы: 8
EAW MX8600 Jumpstart Manual preview
MX8600
Бренд: EAW Страницы: 6
EAW UX8800 Technical Note preview
UX8800
Бренд: EAW Страницы: 6
TC-Helicon PERFORM-VK Quick Start Manual preview
PERFORM-VK
Бренд: TC-Helicon Страницы: 2
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Бренд: D-Link Страницы: 31
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Бренд: NXP Semiconductors Страницы: 24
Endace DAG 7.1S User Manual preview
DAG 7.1S
Бренд: Endace Страницы: 51
Kanguru Data Bank User Manual preview
Data Bank
Бренд: Kanguru Страницы: 13
Renesas RL78/G11 User Manual preview
RL78/G11
Бренд: Renesas Страницы: 2
DCB BROADCAST POLLING FRAD BPF-14 BU Manual preview
BROADCAST POLLING FRAD BPF-14 BU
Бренд: DCB Страницы: 28
ATEN Slideaway CL1008 User Manual preview
Slideaway CL1008
Бренд: ATEN Страницы: 77
EZCast Pro Dongle II D10 Repair Manual preview
Dongle II D10
Бренд: EZCast Pro Страницы: 4
ekwb EK-FC R9-295X2 Installation And Mounting Manual preview
EK-FC R9-295X2
Бренд: ekwb Страницы: 2
National Instruments PCI-6601 User Manual preview
PCI-6601
Бренд: National Instruments Страницы: 52
Multiplex MULTIflight Stick Operating Instructions Manual preview
MULTIflight Stick
Бренд: Multiplex Страницы: 10
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Бренд: Magewell Страницы: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Бренд: Z3 Technology Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды