manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 113 of 760

The following three operations on the address array are possible.

(1) Address Array Read
Reads the tag address, LRU, U bit, and V bit from the entry that corresponds to the entry address
and w`ay that were specified in the address field. No associative operation will be performed,
regardless of the value of the associative bit (the A bit).

(2) Address Array Write (without Associative Operation)
Writes the tag address, LRU, U bit, and V bit specified in the data field to the entry that
corresponds to the entry address and way that were specified in the address field. The associative
bit (A bit) of the address field must be set to 0. An attempt to write to a cache line for which both
the U bit and V bit are set results in a write-back for that cache line. The tag address, LRU, U bit,
and V bit specified in the data field are then written. Note that, when a 0 is written to the V bit, a 0
should always be written to the U bit of the same entry, too.

(3) Address Array Write (with Associative Operation)

The associative bit (A bit) in the address field indicates whether the addresses are compared
during writing. With the A bit set to 1, all 4 ways for the entry specified in the address field will be
compared to the tag address specified in the data field for a match. The values of the U bit and V
bit specified in the data field will be written to the way that has a hit. However, the tag address and
the LRU will not be changed. If no way receives a hit, writing does not take place and the result is
no operation.

This operation is used to invalidate the address specification for a cache. Write back will take
place when the U bit of the entry that received a hit is 1. Note that, when a 0 is written to the V bit,
a 0 should always be written to the U bit of the same entry, too.

5.4.2

Data Array

The address array is mapped to H'F1000000 to H'F1FFFFFF. To access an element of the data
array, the 32-bit address field (for read/write access) and 32-bit data field (for write access) must
be specified. The address field specifies the information that selects the entry to be accessed; the
data field specifies the longword data to be written to the data array.

In the address field, specify the entry's address in bits 11-4, L in bits 3-2 to indicate the longword's
position within a line (which consists of 16 bytes), W in bits 13-12 to select the way, and H'F1 in
bits 31-24 to indicate access to the data array. The L bits (3-2) specification is in the following
form: 00 is longword 0, 01 is longword 1, 10 is longword 2, and 11 is longword 3. Settings for the
W bits (13-12) are as follows: 00 is way 0, 01 is way 1, 10 is way 2, and 11 is way 3. Since access
is not allowed crossing longword boundaries, always set 00 in bits 1-0 of the address field.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

A10 Thunder Series Manual preview
Thunder Series
Бренд: A10 Страницы: 52
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Бренд: 3Com Страницы: 204
Wintech TDS510USB Plus Installation Manual preview
TDS510USB Plus
Бренд: Wintech Страницы: 21
QuickLink QL-CXS Installation Manual preview
QL-CXS
Бренд: QuickLink Страницы: 8
A4Tech RH-10 User Manual preview
RH-10
Бренд: A4Tech Страницы: 8
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Бренд: Pressalit Care Страницы: 31
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Бренд: AMX Страницы: 1
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Бренд: Ista Страницы: 16
Hanwha Techwin Wisenet XRN-6410RB2-24TB User Manual preview
Wisenet XRN-6410RB2-24TB
Бренд: Hanwha Techwin Страницы: 124
Xtreme SNMP-2PV2 User & Installation Manual preview
SNMP-2PV2
Бренд: Xtreme Страницы: 83
Intel BX80637I53570K Specification preview
BX80637I53570K
Бренд: Intel Страницы: 54
Multitech MTDOT-868 Series Developer'S Manual preview
MTDOT-868 Series
Бренд: Multitech Страницы: 60
Rane CP 52S Operator'S Manual preview
CP 52S
Бренд: Rane Страницы: 6
Data Translation DT9835 Getting Started Manual preview
DT9835
Бренд: Data Translation Страницы: 62
Paradyne SMD2000-24E Installation Instructions Manual preview
SMD2000-24E
Бренд: Paradyne Страницы: 28
Boser HS-2605 Manual preview
HS-2605
Бренд: Boser Страницы: 82
Classe Audio CT-SSP Owner'S Manual preview
CT-SSP
Бренд: Classe Audio Страницы: 70
Ublox USB-ANNA-B4 User Manual preview
USB-ANNA-B4
Бренд: Ublox Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды