manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page xxxiv of xliv

Figure 11.23 Timing Chart of Source Address Reload Function............................................... 373
Figure 11.24 Block Diagram of CMT ....................................................................................... 376
Figure 11.25 Counter Operation ................................................................................................ 380
Figure 11.26 Count Timing ....................................................................................................... 381
Figure 11.27 CMF Setting Timing ............................................................................................ 382
Figure 11.28 Timing of CMF Clearing by the CPU .................................................................. 382
Figure 12.1

Block Diagram of TMU ....................................................................................... 390

Figure 12.2

Setting the Count Operation ................................................................................. 401

Figure 12.3

Auto-Reload Count Operation.............................................................................. 402

Figure 12.4

Count Timing when Operating on Internal Clock ................................................ 402

Figure 12.5

Count Timing when Operating on External Clock (Both Edges Detected) .......... 403

Figure 12.6

Count Timing when Operating on On-Chip RTC Clock ...................................... 403

Figure 12.7

Operation Timing when Using Input Capture Function (Using TCLK Rising
Edge) .................................................................................................................... 404

Figure 12.8

UNF Setting Timing............................................................................................. 404

Figure 12.9

Status Flag Clearing Timing................................................................................. 405

Figure 13.1

Block Diagram of RTC ........................................................................................ 408

Figure 13.2

Setting the Time ................................................................................................... 422

Figure 13.3

Reading the Time ................................................................................................. 423

Figure 13.4

Using the Alarm Function .................................................................................... 424

Figure 13.5

Example of Crystal Oscillator Circuit Connection ............................................... 425

Figure 13.6

Using Periodic Interrupt Function ........................................................................ 426

Figure 14.1

Block Diagram of SCI .......................................................................................... 428

Figure 14.2

SCPT[1]/SCK0 Pin .............................................................................................. 429

Figure 14.3

SCPT[0]/TxD0 Pin............................................................................................... 430

Figure 14.4

SCPT[0]/RxD0 Pin............................................................................................... 431

Figure 14.5

Example of Data Format in Asynchronous Communication (8-Bit Data
with Parity and Two Stop Bits) ............................................................................ 455

Figure 14.6

Output Clock and Serial Data Timing (Asynchronous Mode) ............................. 457

Figure 14.7

Sample Flowchart for SCI Initialization............................................................... 458

Figure 14.8

Sample Flowchart for Transmitting Serial Data ................................................... 459

Figure 14.9

Example of SCI Transmit Operation in Asynchronous Mode (8-Bit Data
with Parity and One Stop Bit) .............................................................................. 461

Figure 14.10 Sample Flowchart for Receiving Serial Data ....................................................... 462
Figure 14.11 Example of SCI Receive Operation (8-Bit Data with Parity and One Stop Bit) .. 465
Figure 14.12 Communication Among Processors Using Multiprocessor Format

(Sending Data H'AA to Receiving Processor A) .................................................. 466

Figure 14.13 Sample Flowchart for Transmitting Multiprocessor Serial Data .......................... 467
Figure 14.14 Example of SCI Multiprocessor Transmit Operation (8-Bit Data with

Multiprocessor Bit and One Stop Bit) .................................................................. 468

Figure 14.15 Sample Flowchart for Receiving Multiprocessor Serial Data .............................. 470
Figure 14.16 Example of SCI Receive Operation (8-Bit Data with Multiprocessor Bit and

One Stop Bit)........................................................................................................ 472

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Бренд: ekwb Страницы: 7
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
S&T kontron KBox E-420-R1K/V1K User Manual preview
kontron KBox E-420-R1K/V1K
Бренд: S&T Страницы: 82
HighPoint RocketCache 3240X8 User Manual preview
RocketCache 3240X8
Бренд: HighPoint Страницы: 17
IBM Power System S914 Installing Instructions preview
Power System S914
Бренд: IBM Страницы: 48
Rockwell Automation Trusted T8833 Manual preview
Trusted T8833
Бренд: Rockwell Automation Страницы: 21
SmartBridges airPoint Nexus sB3210 User Manual preview
airPoint Nexus sB3210
Бренд: SmartBridges Страницы: 55
Commell MP-6802 User Manual preview
MP-6802
Бренд: Commell Страницы: 18
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Бренд: Avocent Страницы: 2
ACTi GNR-410 Quick Installation Manual preview
GNR-410
Бренд: ACTi Страницы: 12
Commell MP-6010 User Manual preview
MP-6010
Бренд: Commell Страницы: 17
Opengear OG-HDTV-SDI-UHD User Manual preview
OG-HDTV-SDI-UHD
Бренд: Opengear Страницы: 7
Planet FGSW-4840S User Manual preview
FGSW-4840S
Бренд: Planet Страницы: 38
VALKYRIE Syn 240 Installation Manual preview
Syn 240
Бренд: VALKYRIE Страницы: 26
Curtiss-Wright DTI-VME/S User Manual preview
DTI-VME/S
Бренд: Curtiss-Wright Страницы: 80
Adeunis RF ARF8264AAA Quick Start Manual preview
ARF8264AAA
Бренд: Adeunis RF Страницы: 9
protech ProX-1550 User Manual preview
ProX-1550
Бренд: protech Страницы: 110
Johnson Controls FIRE-MON-17 Technical Manual preview
FIRE-MON-17
Бренд: Johnson Controls Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды