manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 346 of 760

Normal end

AE = 1 or

NMIF = 1 or

DE = 0 or 
DME = 0?

Bus mode,

transfer request mode,

DREQ detection selection

system

Initial settings

(SAR, DAR, DMATCR, CHCR, DMAOR)

Transfer (1 transfer unit);

DMATCR 

−

 1 

→

 DMATCR, 

SAR and DAR updated

DEI interrupt request (when IE = 1)

No

Yes

No

Yes

No

Yes

Yes

No

Yes

No

*

3

*

2 

Start

Transfer aborted

DMATCR = 0?

Transfer request?

*

1

DE, DME = 1 and

AE, NMIF, TE = 0?

Does

AE = 1 or

NMIF = 1 or

DE = 0 or DME

= 0?

Transfer end

Notes: 1. 

In auto-request mode, transfer begins when AE, NMIF, and TE are both 0 and the DE and 
DME bits are set to 1.

 2. 

DREQ

 = level detection in burst mode (external request) or cycle-steal mode.

 3. 

DREQ

 = edge detection in burst mode (external request), or auto-request mode in burst mode.

Figure 11.2   DMAC Transfer Flowchart

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Бренд: Laurell Страницы: 84
TC Electronic DB6 User Manual preview
DB6
Бренд: TC Electronic Страницы: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Бренд: TC Electronic Страницы: 33
Klark Teknik DN9650 Operator'S Manual preview
DN9650
Бренд: Klark Teknik Страницы: 50
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Бренд: LGC wireless Страницы: 154
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Бренд: impinj Страницы: 60
Glacier G2080TiFE Installation Manual preview
G2080TiFE
Бренд: Glacier Страницы: 2
ekwb EK-Loop Modulus Series User Manual preview
EK-Loop Modulus Series
Бренд: ekwb Страницы: 7
Kaptia Klever Getting Started preview
Klever
Бренд: Kaptia Страницы: 14
Medel RONDO 3 Quick Manual preview
RONDO 3
Бренд: Medel Страницы: 28
MEDIATEK MT6252 Design Manual preview
MT6252
Бренд: MEDIATEK Страницы: 166
Arduino ABX00061 Reference Manual preview
ABX00061
Бренд: Arduino Страницы: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Бренд: Divio Страницы: 4
DFRobot FIT0677 Assembly Manual preview
FIT0677
Бренд: DFRobot Страницы: 30
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Бренд: ADLINK Technology Страницы: 48
Advantech SNMP-1000-E2B1E How To Connect preview
SNMP-1000-E2B1E
Бренд: Advantech Страницы: 4
Omron JUNMA PULSE Datasheet preview
JUNMA PULSE
Бренд: Omron Страницы: 4
IceManCooler ICE-SKY-E User Manual preview
ICE-SKY-E
Бренд: IceManCooler Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды