manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 464 of 760

In receiving, the SCI operates as follows:

1. The SCI monitors the communication line. When it detects a start bit (0), the SCI synchronizes

internally and starts receiving.

2. Receive data is shifted into SCRSR in order from the LSB to the MSB.

3. The parity bit and stop bit are received. After receiving these bits, the SCI makes the following

checks:

a. Parity check: The number of 1s in the receive data must match the even or odd parity

setting of the O/

E

 bit in SCSMR.

b. Stop bit check: The stop bit value must be 1. If there are two stop bits, only the first stop bit

is checked.

c. Status check: RDRF must be 0 so that receive data can be loaded from SCRSR into

SCRDR.

If these checks all pass, the SCI sets RDRF to 1 and stores the received data in SCRDR. If
one of the checks fails (receive error), the SCI operates as indicated in table 14.12.

Note:

When a receive error flag is set, further receiving is disabled. The RDRF bit is not set to 1.
Be sure to clear the error flags.

4. After setting RDRF to 1, if the receive-data-full interrupt enable bit (RIE) is set to 1 in

SCSCR, the SCI requests a receive-data-full interrupt (RXI). If one of the error flags (ORER,
PER, or FER) is set to 1 and the receive-data-full interrupt enable bit (RIE) in SCSCR is also
set to 1, the SCI requests a receive-error interrupt (ERI).

Table 14.12 Receive Error Conditions and SCI Operation

Receive Error

Abbreviation

Condition

Data Transfer

Overrun error

ORER

Receiving of next data ends while
RDRF is still set to 1 in SCSSR

Receive data not
transferred from SCRSR
into SCRDR

Framing error

FER

Stop bit is 0

Receive data transferred
from SCRSR into SCRDR

Parity error

PER

Parity of receive data differs from
even/odd parity setting in SCSMR

Receive data transferred
from SCRSR into SCRDR

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

IBM System x3630 M4 Manual preview
System x3630 M4
Бренд: IBM Страницы: 7
Samsung NAS Series Hardware User Manual preview
NAS Series
Бренд: Samsung Страницы: 65
Orban OPTIMOD 6300 Operating Manual preview
OPTIMOD 6300
Бренд: Orban Страницы: 255
Waves MaxxBCL Manual preview
MaxxBCL
Бренд: Waves Страницы: 41
Kaya Instruments KY-FGK Reference Manual preview
KY-FGK
Бренд: Kaya Instruments Страницы: 48
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Бренд: B+B SmartWorx Страницы: 120
DigiTech RP 3 User Manual preview
RP 3
Бренд: DigiTech Страницы: 28
AMD Geode LX 800 User Manual preview
Geode LX 800
Бренд: AMD Страницы: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Бренд: EXAGATE Страницы: 7
Renesas R0E424270CFLE0 User Manual preview
R0E424270CFLE0
Бренд: Renesas Страницы: 4
Matrix Switch Corporation MSC-CP16X4E Product Manual preview
MSC-CP16X4E
Бренд: Matrix Switch Corporation Страницы: 48
Acces I/O products mPCIe-ADI12-8 Hardware Manual preview
mPCIe-ADI12-8
Бренд: Acces I/O products Страницы: 13
Curtiss-Wright GTS/DEC/006 Instructions Manual preview
GTS/DEC/006
Бренд: Curtiss-Wright Страницы: 10
Citizen CBM-606 User Manual preview
CBM-606
Бренд: Citizen Страницы: 29
LiveAction LiveWire Quick Start Manual preview
LiveWire
Бренд: LiveAction Страницы: 2
MikroTik CCR1009-7G-1C-1S+ Quick Manual preview
CCR1009-7G-1C-1S+
Бренд: MikroTik Страницы: 9
SunFounder R3 Manual preview
R3
Бренд: SunFounder Страницы: 527
Bogen PCM-CPU User Manual preview
PCM-CPU
Бренд: Bogen Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды