manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 190 of 760

Canceling with a Reset: Standby mode is canceled by a reset (power-on or manual). Keep the

RESET

 pin low until the clock oscillation settles. The internal clock will continue to be output to

the CKIO and CKIO2 pins.

8.4.3

Clock Pause Function

In standby mode, the clock input from the EXTAL pin or CKIO pin can be halted and the
frequency can be changed. This function is used as follows:

1. Enter standby mode using the appropriate procedures.

2. Once standby mode is entered and the clock stopped within the chip, the STATUS1 pin output

is low and the STATUS0 pin output is high.

3. Once the STATUS1 pin goes low and the STATUS0 pin goes high, the input clock is stopped

or the frequency is changed.

4. When the frequency is changed, an NMI, IRL, IRQ, PINT, or on-chip peripheral module

(except interval timer) interrupt is input after the change. When the clock is stopped, the same
interrupts are input after the clock is applied.

5. After the time set in the WDT has elapsed, the clock starts being applied internally within the

chip, the STATUS1 and STATUS0 pins both go low, and operation resumes from interrupt
exception handling.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

3Com 3CRWB6096 Quick Start Manual preview
3CRWB6096
Бренд: 3Com Страницы: 8
Ubiquiti NanoBeam M5 Setup preview
NanoBeam M5
Бренд: Ubiquiti Страницы: 3
Yamaha DX7mega128 Install Manual preview
DX7mega128
Бренд: Yamaha Страницы: 6
Yamaha DX7 MiniMAX User Manual preview
DX7 MiniMAX
Бренд: Yamaha Страницы: 4
Yamaha DME Designer Setup Manual preview
DME Designer
Бренд: Yamaha Страницы: 22
Yamaha PLG100-VL Eigentümer-Handbuch preview
PLG100-VL
Бренд: Yamaha Страницы: 49
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Бренд: M86 Security Страницы: 46
Alcad ZA-431 Quick Start Manual preview
ZA-431
Бренд: Alcad Страницы: 6
Quectel Wi-Fi-M.2 EVB User Manual preview
Wi-Fi-M.2 EVB
Бренд: Quectel Страницы: 23
Bridgeworks a204 Hardware Manual preview
a204
Бренд: Bridgeworks Страницы: 18
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Бренд: ADC Страницы: 7
Renesas Emulator MCU Board for 38D5 Group M38D59T-RLFS User Manual preview
Emulator MCU Board for 38D5 Group M38D59T-RLFS
Бренд: Renesas Страницы: 4
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Бренд: Bose Страницы: 2
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Бренд: Concept Pro Страницы: 28
Omron F3SP-U3P-TGR User Manual preview
F3SP-U3P-TGR
Бренд: Omron Страницы: 29
Freescale Semiconductor M68HC08 series Designer Reference Manual preview
M68HC08 series
Бренд: Freescale Semiconductor Страницы: 124
MESA Electronic 4C24 Manual preview
4C24
Бренд: MESA Electronic Страницы: 27
Safety Vision ROADRECORDER 8400 NVR User Manual preview
ROADRECORDER 8400 NVR
Бренд: Safety Vision Страницы: 27

Бренды по названию

Популярные бренды

Загрузить еще бренды