manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 442 of 760

Bit 4—Framing Error (FER): Indicates that data reception aborted due to a framing error in
asynchronous mode.

Bit 4: FER

Description

0

Receiving is in progress or has ended normally

*

1

 (Initial value)

[Clearing conditions]

(1) FER is cleared to 0 when the chip is reset or enters standby mode.

(2) When software reads FER after it has been set to 1, then writes 0 to FER.

1

A receive framing error occurred

[Setting condition]

FER is set to 1 if the stop bit at the end of receive data is checked and found to
be 0.

*

2

Notes: 1. Clearing the RE bit to 0 in the serial control register does not affect the FER bit, which

retains its previous value.

2. When the stop bit length is two bits, only the first bit is checked. The second stop bit is

not checked. When a framing error occurs, the SCI transfers the receive data into
SCRDR but does not set RDRF. Serial receiving cannot continue while FER is set to 1.
In synchronous mode, serial transmitting is also disabled.

Bit 3—Parity Error (PER): Indicates that data reception (with parity) aborted due to a parity
error in asynchronous mode.

Bit 3: PER

Description

0

Receiving is in progress or has ended normally

*

1

(Initial value)

[Clearing conditions]

(1) PER is cleared to 0 when the chip is reset or enters standby mode.

(2) When software reads PER after it has been set to 1, then writes 0 to PER.

1

A receive parity error occurred

*

2

[Setting condition]

PER is set to 1 if the number of 1s in receive data, including the parity bit, does
not match the even or odd parity setting of the parity mode bit (O/

E

) in the serial

mode register (SCSMR).

Notes: 1. Clearing the RE bit to 0 in the serial control register does not affect the PER bit, which

retains its previous value.

2. When a parity error occurs, the SCI transfers the receive data into SCRDR but does not

set RDRF. Serial receiving cannot continue while PER is set to 1. In synchronous
mode, serial transmitting is also disabled.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Vivotek NR8401 User Manual preview
NR8401
Бренд: Vivotek Страницы: 136
Stanwax Laser S4i Manual preview
S4i
Бренд: Stanwax Laser Страницы: 9
Belkin F5D9001 Series Manual preview
F5D9001 Series
Бренд: Belkin Страницы: 72
ICT Protege PRT-PX16-PCB Installation Manual preview
Protege PRT-PX16-PCB
Бренд: ICT Страницы: 34
MC PCIe-DIO96H User Manual preview
PCIe-DIO96H
Бренд: MC Страницы: 21
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Бренд: Jaycar Electronics Страницы: 2
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Бренд: Dahua Страницы: 452
ekwb EK-FC750 GTX Series Installation Manual preview
EK-FC750 GTX Series
Бренд: ekwb Страницы: 2
IFM QHA200 Instructions For Setup preview
QHA200
Бренд: IFM Страницы: 12
Variscite VAR-SOM-MX8M-PLUS Quick Start Manual preview
VAR-SOM-MX8M-PLUS
Бренд: Variscite Страницы: 2
ETAS XETK-S21.0B User Manual preview
XETK-S21.0B
Бренд: ETAS Страницы: 68
ActiveEye K9504L-W Operation Manual preview
K9504L-W
Бренд: ActiveEye Страницы: 35
Moxa Technologies Smartio CP-104UL Quick Installation Manual preview
Smartio CP-104UL
Бренд: Moxa Technologies Страницы: 2
LanReady AP-952X User Manual preview
AP-952X
Бренд: LanReady Страницы: 40
Azoteq IQ Switch ProxSense RS100 Application Notes preview
IQ Switch ProxSense RS100
Бренд: Azoteq Страницы: 9
HeimVision HM243 User Manual preview
HM243
Бренд: HeimVision Страницы: 167
Asus Aaeon UPN Edge Pro User Manual preview
Aaeon UPN Edge Pro
Бренд: Asus Страницы: 55
Asus AGP-V3100 User Manual preview
AGP-V3100
Бренд: Asus Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды