manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 526 of 760

Bit 1—Receive FIFO Data Full (RDF): Indicates that receive data has been transferred to the
receive FIFO data register (SCFRDR), and the quantity of data in SCFRDR has become greater
than the receive trigger number specified by the RTRG1 and RTRG0 bits in the FIFO control
register (SCFCR).

Bit 1: RDF

Description

0

The quantity of transmit data written to SCFRDR is less than the specified
receive trigger number

(Initial value)

[Clearing conditions]

(1) By a power-on reset or in standby mode

(2) When the quantity of receive data in SCFRDR is less than the specified

receive trigger value and 1 is read from RDF, which is then cleared to 0

1

The quantity of receive data in SCFRDR is greater than the specified receive
trigger number

[Setting condition]

When a quantity of receive data greater than the specified receive trigger number
is stored in SCFRDR

*

Note:  

*

Since SCFTDR is a 16-byte FIFO register, the maximum quantity of data that can be read
when RDF is 1 is the specified receive trigger number. If an attempt is made to read after
all the data in SCFRDR has been read, the data is undefined. The quantity of receive data
in SCFRDR is indicated by the lower 8 bits of SCFTDR.

Bit 0—Receive Data Ready (DR): Indicates that the quantity of data in the receive FIFO data
register (SCFRDR) is less than the specified receive trigger number, and that the next data has not
yet been received after the elapse of 15 etu from the last stop bit.

Bit 0: DR

Description

0

Receiving is in progress, or no receive data remains in SCFRDR after receiving
ended normally

(Initial value)

[Clearing conditions]

(1) When the chip undergoes a power-on reset or enters standby mode

(2) When software reads DR after it has been set to 1, then writes 0 to DR

1

Next receive data has not been received

[Setting condition]

When SCFRDR contains less data than the specified receive trigger number,
and the next data has not yet been received after the elapse of 15 etu from the
last stop bit

*

Note:  

*

This is equivalent to 1.5 frames with the 8-bit, 1-stop-bit format. (etu: elementary time unit)

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Lanner NCA-2510 Installation Manual preview
NCA-2510
Бренд: Lanner Страницы: 2
Vonets MINI300 Quick Setting Manual preview
MINI300
Бренд: Vonets Страницы: 8
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Бренд: Ubiquiti Страницы: 13
Renesas Converter Board R0E521237CFK00 User Manual preview
Converter Board R0E521237CFK00
Бренд: Renesas Страницы: 6
Rolls HR11C - SCHEMA Wiring Diagram preview
HR11C - SCHEMA
Бренд: Rolls Страницы: 1
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Бренд: Intel Страницы: 105
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Бренд: Promise Technology Страницы: 26
Holtek HT68F30 Manual preview
HT68F30
Бренд: Holtek Страницы: 280
Thermalright Macho Rev. A (BW) Manual preview
Macho Rev. A (BW)
Бренд: Thermalright Страницы: 32
Supermicro BPN-SAS3-116A-N10 User Manual preview
BPN-SAS3-116A-N10
Бренд: Supermicro Страницы: 8
ekwb 3831109810316 User Manual preview
3831109810316
Бренд: ekwb Страницы: 16
IBM SA23-1325-01 Installation And Using Manual preview
SA23-1325-01
Бренд: IBM Страницы: 44
Ezquest Boa K16766 User Manual preview
Boa K16766
Бренд: Ezquest Страницы: 65
NEC N8151-53 User Manual preview
N8151-53
Бренд: NEC Страницы: 114
Ametek Land System 4 Landmark Technic Processor User Manual preview
System 4 Landmark Technic Processor
Бренд: Ametek Land Страницы: 34
Omega Engineering BNC-08DI, BNC-16DI, BNC-16SE User Manual preview
BNC-08DI, BNC-16DI, BNC-16SE
Бренд: Omega Engineering Страницы: 25
Tektronix 7B87 Instruction Manual preview
7B87
Бренд: Tektronix Страницы: 143
Westlock Controls Corporation Intellis 7604 Installation And Operation Manual preview
Intellis 7604
Бренд: Westlock Controls Corporation Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды