manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 319 of 760

10.3.7

Waits between Access Cycles

A problem associated with higher external memory bus operating frequencies is that data buffer
turn-off on completion of a read from a low-speed device may be too slow, causing a collision
with data in the next access. This results in lower reliability or incorrect operation. To avoid this
problem, a data collision prevention feature has been provided. This memorizes the preceding
access area and the kind of read/write. If there is a possibility of a bus collision when the next
access is started, a wait cycle is inserted before the access cycle thus preventing a data collision.
There are two cases in which a wait cycle is inserted: when an access is followed by an access to a
different area, and when a read access is followed by a write access from the SH7709S. When the
SH7709S performs consecutive write cycles, the data transfer direction is fixed (from the
SH7709S to other memory) and there is no problem. With read accesses to the same area, in
principle, data is output from the same data buffer, and wait cycle insertion is not performed. Bits
AnIW1 and AnIW0 (n = 0, 2–6) in WCR1 specify the number of idle cycles to be inserted
between access cycles when a physical space area access is followed by an access to another area,
or when the SH7709S performs a write access after a read access to physical space area n. If there
is originally space between accesses, the number of idle cycles inserted is the specified number of
idle cycles minus the number of empty cycles.

Waits are not inserted between accesses when bus arbitration is performed, since empty cycles are
inserted for arbitration purposes.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Бренд: ABB Страницы: 44
DBM ACE9600 Operating Manual preview
ACE9600
Бренд: DBM Страницы: 50
Z3 Technology Z3-DM8168-PCI-RPS Manual preview
Z3-DM8168-PCI-RPS
Бренд: Z3 Technology Страницы: 20
Z3 Technology Z3-DM8107-SDI2-RPS User Manual preview
Z3-DM8107-SDI2-RPS
Бренд: Z3 Technology Страницы: 75
Z-Wave USB Dongle User Manual preview
USB Dongle
Бренд: Z-Wave Страницы: 13
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Бренд: Idis Страницы: 86
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Бренд: Paradyne Страницы: 2
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Бренд: Renesas Страницы: 17
Dialogic EDP-10 Quick Install Manual preview
EDP-10
Бренд: Dialogic Страницы: 2
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Бренд: Delta Electronics Страницы: 1
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Бренд: Longshine Страницы: 27
Ubiquiti LiteBeam M5-23 Quick Start Manual preview
LiteBeam M5-23
Бренд: Ubiquiti Страницы: 21
IBASE Technology FWA8207 Series User Manual preview
FWA8207 Series
Бренд: IBASE Technology Страницы: 39
Cameo WLG-1801 User Manual preview
WLG-1801
Бренд: Cameo Страницы: 23
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Бренд: Intel Страницы: 86
Freescale Semiconductor MPC8349EA MDS Getting Started Manual preview
MPC8349EA MDS
Бренд: Freescale Semiconductor Страницы: 8
Swann NVRx-7300 series Quick Start Manual preview
NVRx-7300 series
Бренд: Swann Страницы: 9
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Бренд: ANEP Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды