manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 58 of 760

3.1.3

SH7709S MMU

Virtual Address Space: The SH7709S uses 32-bit virtual addresses to access a 4-Gbyte virtual
address space that is divided into several areas. Address space mapping is shown in figure 3.2.

•

 

Privileged Mode

In privileged mode, there are five areas, P0–P4. The P0 and P3 areas are mapped onto physical
address space in page units, in accordance with address translation table information. Write-
back or write-through can be selected for write access by means of a cache control register
(CCR) setting.

Mapping of the P1 area is fixed in physical address space (H'00000000 to H'1FFFFFFF).  In
the P1 area, setting a virtual address MSB (bit 31) to 0 generates the corresponding physical
address.  P1 area accesses can be cached, and the cache control register (CCR) is set to indicate
whether to cache or not.  Write-back or write-through mode can be selected.

Mapping of the P2 area is fixed in physical address space (H'00000000 to H'1FFFFFFF). In the
P2 area, setting the top three virtual address bits (bits 31, 30, and 29) to 0 generates the
corresponding physical address. P2 area access cannot be cached.

The P1 and P2 areas are not mapped by the address translation table, so the TLB is not used
and no exceptions such as TLB misses occur. Initialization of MMU control registers,
exception handling routines, and the like should be located in the P1 and P2 areas. Routines
that require high-speed processing should be placed in the P1 area, since it can be cached.

Some peripheral module control registers are located in area 1 of the physical address space.
When the physical address space is not used for address translation, these registers should be
located in the P2 area. When address translation is to be used, set no caching.

The P4 area is used for mapping peripheral module register addresses, etc.

•

 

User Mode

In user mode, 2 Gbytes of the virtual address space from H'00000000 to H'7FFFFFFF (area
U0) can be accessed. U0 is mapped onto physical address space in page units, in accordance
with address translation table information.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 5
Acconeer A111 User Manual preview
A111
Бренд: Acconeer Страницы: 32
XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Бренд: XMOS Страницы: 112
Delta Tau PMAC2-PC/104 Installation Manual preview
PMAC2-PC/104
Бренд: Delta Tau Страницы: 74
Renesas Converter Board R0E5212BACFG00 User Manual preview
Converter Board R0E5212BACFG00
Бренд: Renesas Страницы: 6
ebm-papst R3G175-AF01-02 Operating Instructions Manual preview
R3G175-AF01-02
Бренд: ebm-papst Страницы: 11
SAB SABVISION NVR32 Quick Start Manual preview
SABVISION NVR32
Бренд: SAB Страницы: 29
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Бренд: JUMO Страницы: 41
TDK HHM Series HHM2245SA1 Specifications preview
HHM Series HHM2245SA1
Бренд: TDK Страницы: 2
Medel RONDO 3 Quick Manual preview
RONDO 3
Бренд: Medel Страницы: 28
Thermaltake Extreme Spirit Il Instruction preview
Extreme Spirit Il
Бренд: Thermaltake Страницы: 2
Crest Audio NC-MCO - TECHNICAL Technical Data preview
NC-MCO - TECHNICAL
Бренд: Crest Audio Страницы: 2
Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011 Datasheet preview
2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011
Бренд: Intel Страницы: 172
ADLINK Technology AMC-7000 User Manual preview
AMC-7000
Бренд: ADLINK Technology Страницы: 34
TECO e-chill 1 Instruction Manual preview
e-chill 1
Бренд: TECO Страницы: 24
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Бренд: ZyXEL Communications Страницы: 114
iTON ID6ZFN-BK0 User Manual preview
ID6ZFN-BK0
Бренд: iTON Страницы: 12
Xilinx SelectIO 7 Series User Manual preview
SelectIO 7 Series
Бренд: Xilinx Страницы: 188

Бренды по названию

Популярные бренды

Загрузить еще бренды