manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 510 of 760

Retransmission when SCI is in Transmit Mode: Figure 15.10 shows the retransmission
operation in the SCI transmit mode.

1. After transmission of one frame is completed, the FER/ERS bit in SCSSR is set to 1 when a

error signal is returned from the receiving side. If the RIE bit in SCSCR is enabled at this time,
an ERI interrupt is requested. Be sure to clear the FER/ERS bit before the next parity bit is
sampled.

2. The TEND bit in SCSSR is not set in the frame that received the error signal indicating the

error.

3. The FER/ERS bit in SCSSR is not set when no error signal is returned from the receiving side.

4. When no error signal is returned from the receiving side, the TEND bit in SCSSR is set to 1

when the transmission of the frame that includes the retransmission is considered completed. If
the TIE bit in SCSCR is enabled at this time, a TXI interrupt will be requested.

D0

Ds

D2

D1

D4

D3

D6

D5

Dp DE

D7

D0

Ds

D2

D1

D4

D3

D6

D5

Dp

(DE)

D7

D0

Ds

D2

D1

D4

D3

nth transfer frame

TEND

FER/ERS

Transfer from SCTDR 
to SCTSR

Transfer from SCTDR 
to SCTSR

Transfer from SCTDR 
to SCTSR

1

2

4

3

Retransmitted frame

Transfer frame n + 1

TDRE

Figure 15.10   Retransmission in SCI Transmit Mode

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Datasat AP25 Installation And Operating Manual preview
AP25
Бренд: Datasat Страницы: 170
IBM 8677 - BladeCenter Rack-mountable - Power... Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power...
Бренд: IBM Страницы: 126
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Бренд: ZALMAN Страницы: 7
Advantech ARK-1380 User Manual preview
ARK-1380
Бренд: Advantech Страницы: 50
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Бренд: ZoneVu Страницы: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Бренд: FUNcube Страницы: 23
ICOP Technology Vortex86SX VSX-6100 User Manual preview
Vortex86SX VSX-6100
Бренд: ICOP Technology Страницы: 50
IEI Technology Mustang-M2AE-MX1 User Manual preview
Mustang-M2AE-MX1
Бренд: IEI Technology Страницы: 58
Paradyne JetFusion 2004 User Manual preview
JetFusion 2004
Бренд: Paradyne Страницы: 216
MA Master Fader 1 User Manual preview
Master Fader 1
Бренд: MA Страницы: 4
NAUTICAST 300 2001 Product Manual preview
300 2001
Бренд: NAUTICAST Страницы: 20
Siklu EtherHaul 500 Installation Manual preview
EtherHaul 500
Бренд: Siklu Страницы: 52
Alcatel-Lucent 1677 Brochure preview
1677
Бренд: Alcatel-Lucent Страницы: 8
C-Data FD612H User Manual preview
FD612H
Бренд: C-Data Страницы: 19
NetApp StorageGRID Webscale SG5700 Series Install preview
StorageGRID Webscale SG5700 Series
Бренд: NetApp Страницы: 15
Crestron HZA-PWR-15A Quick Start preview
HZA-PWR-15A
Бренд: Crestron Страницы: 2
Ekselans 250022 User Manual preview
250022
Бренд: Ekselans Страницы: 5
Dell A2463645 - 2 GB Memory Manuallines preview
A2463645 - 2 GB Memory
Бренд: Dell Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды