manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page xli of xliv

Table 13.2

RTC Registers......................................................................................................... 410

Table 13.3

Day-of-Week Codes (RWKCNT) .......................................................................... 413

Table 13.4

Day-of-Week Codes (RWKAR) ............................................................................. 417

Table 13.5

Recommended Oscillator Circuit Constants (Recommended Values).................... 425

Table 14.1

SCI Pins ................................................................................................................. 431

Table 14.2

SCI Registers .......................................................................................................... 432

Table 14.3

SCSMR Settings ..................................................................................................... 446

Table 14.4

Bit Rates and SCBRR Settings in Asynchronous Mode ......................................... 447

Table 14.5

Bit Rates and SCBRR Settings in Synchronous Mode ........................................... 450

Table 14.6

Maximum Bit Rates for Various Frequencies with Baud Rate Generator
(Asynchronous Mode) ............................................................................................ 451

Table 14.7

Maximum Bit Rates with External Clock Input (Asynchronous Mode) ................. 452

Table 14.8

Maximum Bit Rates with External Clock Input (Synchronous Mode) ................... 452

Table 14.9

Serial Mode Register Settings and SCI Communication Formats .......................... 454

Table 14.10 SCSMR and SCSCR Settings and SCI Clock Source Selection ............................. 454
Table 14.11 Serial Communication Formats (Asynchronous Mode) ......................................... 456
Table 14.12 Receive Error Conditions and SCI Operation......................................................... 464
Table 14.13 SCI Interrupt Sources ............................................................................................. 484
Table 14.14 SCSSR Status Flags and Transfer of Receive Data ................................................ 485
Table 15.1

Smart Card Interface Pins ....................................................................................... 491

Table 15.2

Registers ................................................................................................................. 491

Table 15.3

Register Settings for Smart Card Interface ............................................................. 497

Table 15.4

Relationship of n to CKS1 and CKS0..................................................................... 499

Table 15.5

Examples of Bit Rate B (Bits/s) for SCBRR Settings (n 

=

 0)................................. 499

Table 15.6

Examples of SCBRR Settings for Bit Rate B (Bits/s) (n 

=

 0)................................. 499

Table 15.7

Maximum Bit Rates for Frequencies (Smart Card Interface Mode) ....................... 500

Table 15.8

Register Set Values and SCK Pin ........................................................................... 500

Table 15.9

Smart Card Mode Operating State and Interrupt Sources....................................... 507

Table 16.1

SCIF Pins ................................................................................................................ 515

Table 16.2

SCIF Registers ........................................................................................................ 516

Table 16.3

SCSMR Settings ..................................................................................................... 528

Table 16.4

Bit Rates and SCBRR Settings ............................................................................... 528

Table 16.5

Maximum Bit Rates for Various Frequencies with Baud Rate Generator
(Asynchronous Mode) ............................................................................................ 532

Table 16.6

Maximum Bit Rates with External Clock Input (Asynchronous Mode) ................. 533

Table 16.7

SCSMR Settings and SCIF Communication Formats ............................................ 537

Table 16.8

SCSCR Settings and SCIF Clock Source Selection................................................ 538

Table 16.9

Serial Communication Formats .............................................................................. 538

Table 16.10 SCIF Interrupt Sources ........................................................................................... 550
Table 17.1

IrDA Pins ................................................................................................................ 559

Table 17.2

IrDA Registers ........................................................................................................ 560

Table 18.1

List of Multiplexed Pins ......................................................................................... 565

Table 18.2

Pin Function Controller Registers........................................................................... 569

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

ZETR 25 Installation Manual preview
25
Бренд: ZETR Страницы: 2
Laird OL 4503 Specification And User Manual preview
OL 4503
Бренд: Laird Страницы: 36
National Instruments PXIe-8240 Getting Started preview
PXIe-8240
Бренд: National Instruments Страницы: 9
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Бренд: National Instruments Страницы: 8
Paradyne 3172 Quick Reference preview
3172
Бренд: Paradyne Страницы: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Бренд: Paradyne Страницы: 2
Dahua NVR2104-S2 Quick Start Manual preview
NVR2104-S2
Бренд: Dahua Страницы: 6
Black Box JPM083A Manual preview
JPM083A
Бренд: Black Box Страницы: 9
Nvidia nForce 680I LT SLI Hardware User Manual preview
nForce 680I LT SLI
Бренд: Nvidia Страницы: 80
ebm-papst D3G146-LT13-30 Operating Instructions Manual preview
D3G146-LT13-30
Бренд: ebm-papst Страницы: 11
YASKAWA PG-Z2 Instructions Manual preview
PG-Z2
Бренд: YASKAWA Страницы: 15
DAD DXZ48 User Manual preview
DXZ48
Бренд: DAD Страницы: 16
Addonics Technologies ADSA2 Installation Manual preview
ADSA2
Бренд: Addonics Technologies Страницы: 1
National Instruments SCXI-1120 User Manual preview
SCXI-1120
Бренд: National Instruments Страницы: 130
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Бренд: Z3 Technology Страницы: 67
Patton electronics FORESIGHT 6300 User Manual preview
FORESIGHT 6300
Бренд: Patton electronics Страницы: 145
VCS VIP 1000 User Manual preview
VIP 1000
Бренд: VCS Страницы: 118
Observint NVR16 Firmware User Manual preview
NVR16
Бренд: Observint Страницы: 117

Бренды по названию

Популярные бренды

Загрузить еще бренды