manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 519 of 760

Bit 5—Parity Enable (PE): Selects whether to add a parity bit to transmit data and to check the
parity of receive data.

Bit 5: PE

Description

0

Parity bit not added or checked

(Initial value)

1

Parity bit added and checked

*

Note:  

*

When PE is set to 1, an even or odd parity bit is added to transmit data, depending on the
parity mode (O/

E

) setting. Receive data parity is checked according to the even/odd (O/

E

)

mode setting.

Bit 4—Parity Mode (O/

E

EE

E

): Selects even or odd parity when parity bits are added and checked.

The O/

E

 setting is used only when the parity enable bit (PE) is set to 1 to enable parity addition

and checking. The O/

E

 setting is ignored when parity addition and checking is disabled.

Bit 4: O/

E

E

E

E

Description

0

Even parity

*

1

(Initial value)

1

Odd parity

*

2

Notes: 1. If even parity is selected, the parity bit is added to transmit data to make an even

number of 1s in the transmitted character and parity bit combined. Receive data is
checked to see if it has an even number of 1s in the received character and parity bit
combined.

2. If odd parity is selected, the parity bit is added to transmit data to make an odd number

of 1s in the transmitted character and parity bit combined. Receive data is checked to
see if it has an odd number of 1s in the received character and parity bit combined.

Bit 3—Stop Bit Length (STOP): Selects one or two bits as the stop bit length.

When receiving, only the first stop bit is checked, regardless of the STOP bit setting. If the second
stop bit is 1, it is treated as a stop bit, but if the second stop bit is 0, it is treated as the start bit of
the next incoming character.

Bit 3: STOP

Description

0

One stop bit

*

1

(Initial value)

1

Two stop bits

*

2

Notes: 1. When transmitting, a single 1-bit is added at the end of each transmitted character.

2. When transmitting, two 1-bits are added at the end of each transmitted character.

Bit 2—Reserved: This bit is always read as 0. The write value should always be 0.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Бренд: Cabletron Systems Страницы: 21
Ebyte E43-900T13S3 Manual preview
E43-900T13S3
Бренд: Ebyte Страницы: 8
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Бренд: Ubiquiti Страницы: 23
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Бренд: Paradyne Страницы: 45
Renesas F-ZTAT H8/3048 Series User Manual preview
F-ZTAT H8/3048 Series
Бренд: Renesas Страницы: 34
Oracle Talari E1000 Installation Manual preview
Talari E1000
Бренд: Oracle Страницы: 24
Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Бренд: Moxa Technologies Страницы: 19
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Бренд: Tandberg Data Страницы: 28
Fostex DE-1 Service Manual preview
DE-1
Бренд: Fostex Страницы: 20
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Бренд: Balluff Страницы: 12
Tandy 26-3814 Operation Manual preview
26-3814
Бренд: Tandy Страницы: 24
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Бренд: Comtrend Corporation Страницы: 4
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Бренд: PairGain Страницы: 80
Altimium CVHH2 User Manual preview
CVHH2
Бренд: Altimium Страницы: 12
Serial Cables PCI4-AD-x16HI-BG4 User Manual preview
PCI4-AD-x16HI-BG4
Бренд: Serial Cables Страницы: 15
ANTAIRA MSC-208A2 Installation Manual preview
MSC-208A2
Бренд: ANTAIRA Страницы: 6
Cabletron Systems TRXMIM-24A User Manual preview
TRXMIM-24A
Бренд: Cabletron Systems Страницы: 56
Transition Networks E-BR-SIC User Manual preview
E-BR-SIC
Бренд: Transition Networks Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды