manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page xxxvi of xliv

Figure 19.8

Port H ................................................................................................................... 601

Figure 19.9

Port J .................................................................................................................... 603

Figure 19.10 Port K ................................................................................................................... 605
Figure 19.11 Port L.................................................................................................................... 607
Figure 19.12 SC Port ................................................................................................................. 609
Figure 20.1

Block Diagram of A/D Converter ........................................................................ 614

Figure 20.2

A/D Data Register Access Operation (Reading H'AA40) .................................... 622

Figure 20.3

Example of A/D Converter Operation (Single Mode, Channel 1 Selected) ......... 624

Figure 20.4

Example of A/D Converter Operation (Multi Mode, Channels AN0 to AN2
Selected) ............................................................................................................... 626

Figure 20.5

Example of A/D Converter Operation (Scan Mode, Channels AN0 to AN2
Selected) ............................................................................................................... 628

Figure 20.6

A/D Conversion Timing ....................................................................................... 629

Figure 20.7

External Trigger Input Timing ............................................................................. 630

Figure 20.8

Definitions of A/D Conversion Accuracy ............................................................ 632

Figure 20.9

Example of Analog Input Protection Circuit ........................................................ 633

Figure 20.10 Analog Input Pin Equivalent Circuit .................................................................... 633
Figure 21.1

Block Diagram of D/A Converter ........................................................................ 635

Figure 21.2

Example of D/A Converter Operation.................................................................. 639

Figure 22.1

Block Diagram of UDI ......................................................................................... 642

Figure 22.2

TAP Controller State Transitions ......................................................................... 651

Figure 22.3

UDI Reset............................................................................................................. 653

Figure 23.1

EXTAL Clock Input Timing ................................................................................ 665

Figure 23.2

CKIO Clock Input Timing ................................................................................... 665

Figure 23.3

CKIO Clock Output Timing ................................................................................. 665

Figure 23.4

Power-on Oscillation Settling Time ..................................................................... 666

Figure 23.5

Oscillation Settling Time at Standby Return (Return by Reset)........................... 666

Figure 23.6

Oscillation Settling Time at Standby Return (Return by NMI)............................ 667

Figure 23.7

Oscillation Settling Time at Standby Return (Return by IRQ4 to IRQ0,
PINT0/1, 

IRL3

 to 

IRL0

)....................................................................................... 667

Figure 23.8

PLL Synchronization Settling Time during Standby Recovery (Reset or NMI) .. 668

Figure 23.9

PLL Synchronization Settling Time during Standby Recovery (IRQ/IRL or
PINT0/PINT1 Interrupt)....................................................................................... 668

Figure 23.10 PLL Synchronization Settling Time when Frequency Multiplication Rate

Modified ............................................................................................................... 669

Figure 23.11 Reset Input Timing............................................................................................... 671
Figure 23.12 Interrupt Signal Input Timing............................................................................... 671
Figure 23.13

IRQOUT

 Timing .................................................................................................. 671

Figure 23.14 Bus Release Timing.............................................................................................. 672
Figure 23.15 Pin Drive Timing at Standby ................................................................................ 672
Figure 23.16 Basic Bus Cycle (No Wait) .................................................................................. 675
Figure 23.17 Basic Bus Cycle (One Wait)................................................................................. 676
Figure 23.18 Basic Bus Cycle (External Wait, WAITSEL = 1) ................................................ 677

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Бренд: Delta Electronics Страницы: 1
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Бренд: IEI Technology Страницы: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Бренд: Dahua Technology Страницы: 14
Endace DAG 7.1S User Manual preview
DAG 7.1S
Бренд: Endace Страницы: 51
addlink SPIDER N4 Installation Manual preview
SPIDER N4
Бренд: addlink Страницы: 9
SIIG 1394 Dual-Port CardBus Quick Installation Manual preview
1394 Dual-Port CardBus
Бренд: SIIG Страницы: 8
Bitspower BPTA-CPUMS-V2-SKA Instruction Manual preview
BPTA-CPUMS-V2-SKA
Бренд: Bitspower Страницы: 6
Keil RTX51 Manual preview
RTX51
Бренд: Keil Страницы: 68
Ultra Products Internal All-in-One Digital Media Drive ULT31793 Specifications preview
Internal All-in-One Digital Media Drive ULT31793
Бренд: Ultra Products Страницы: 1
Intellinet 560665 User Manual preview
560665
Бренд: Intellinet Страницы: 32
PACOM PPRO-UR-4EDX Quick Manual preview
PPRO-UR-4EDX
Бренд: PACOM Страницы: 16
Garland EdgeSafe M40G1AC User Manual preview
EdgeSafe M40G1AC
Бренд: Garland Страницы: 159
UltrArmor UA3 Series User Manual preview
UA3 Series
Бренд: UltrArmor Страницы: 3
ubiquoss U9016B Installation Manual preview
U9016B
Бренд: ubiquoss Страницы: 46
Crestron C2N-IO Installation Manual preview
C2N-IO
Бренд: Crestron Страницы: 2
Hitachi KNX001 Installation And Operation Manual preview
KNX001
Бренд: Hitachi Страницы: 14
Hitachi SJ/L-EN Ethernet Communications Module Instruction Manual preview
SJ/L-EN Ethernet Communications Module
Бренд: Hitachi Страницы: 36
Hitachi 3080 G2 Hardware Reference Manual preview
3080 G2
Бренд: Hitachi Страницы: 129

Бренды по названию

Популярные бренды

Загрузить еще бренды