manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 481 of 760

Error handling

End

ORER = 1?

No

Clear ORER bit in SCSSR to 0

Yes

Overrun error handling

Figure 14.21   Sample Flowchart for Receiving Serial Data (cont)

In receiving, the SCI operates as follows:

1. The SCI synchronizes with serial clock input or output and initializes internally.

2. Receive data is shifted into SCRSR in order from the LSB to the MSB. After receiving the

data, the SCI checks that RDRF is 0 so that receive data can be loaded from SCRSR into
SCRDR. If this check is passed, the SCI sets RDRF to 1 and stores the received data in
SCRDR. If the check is not passed (receive error), the SCI operates as indicated in table 14.12.
This state prevents further transmission or reception. While receiving, the RDRF bit is not set
to 1. Be sure to clear the error flag.

3. After setting RDRF to 1, if the receive-data-full interrupt enable bit (RIE) is set to 1 in

SCSCR, the SCI requests a receive-data-full interrupt (RXI). If the ORER bit is set to 1 and the
receive-data-full interrupt enable bit (RIE) in SCSCR is also set to 1, the SCI requests a
receive-error interrupt (ERI).

Figure 14.22 shows an example of SCI receive operation.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

GE MDS SD Series Setup Manual preview
MDS SD Series
Бренд: GE Страницы: 4
Sun Microsystems Ray 3 Plus Client Getting Started Manual preview
Ray 3 Plus Client
Бренд: Sun Microsystems Страницы: 6
IBM AS/400 Hardware User Manual preview
AS/400
Бренд: IBM Страницы: 104
IBM System Storage TS3100 Setup, Operator, And Service Manual preview
System Storage TS3100
Бренд: IBM Страницы: 375
IEI Technology KINO-KBN-i2 Quick Installation Manual preview
KINO-KBN-i2
Бренд: IEI Technology Страницы: 21
Xinje XG Series User Manual preview
XG Series
Бренд: Xinje Страницы: 76
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Бренд: Ubiquiti Страницы: 23
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Бренд: mikroElektronika Страницы: 3
Commell CMB-673 Installation Manual preview
CMB-673
Бренд: Commell Страницы: 9
Renesas Compact Emulator M30620T-CPE User Manual preview
Compact Emulator M30620T-CPE
Бренд: Renesas Страницы: 52
Neo Instruments Mini Vent User Manual preview
Mini Vent
Бренд: Neo Instruments Страницы: 2
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Бренд: Softing Страницы: 4
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Бренд: M86 Security Страницы: 309
TDK HHM Series HHM2245SA1 Specifications preview
HHM Series HHM2245SA1
Бренд: TDK Страницы: 2
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Бренд: NKE Страницы: 15
sound4 STREAM X Maintenance And Operation Instruction Manual preview
STREAM X
Бренд: sound4 Страницы: 66
MCT MPU100ZW User Manual preview
MPU100ZW
Бренд: MCT Страницы: 12
Beckhoff CU8210-D001-0200 Manual preview
CU8210-D001-0200
Бренд: Beckhoff Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды