manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page xxxv of xliv

Figure 14.17 Data Format in Synchronous Communication ..................................................... 474
Figure 14.18 Sample Flowchart for SCI Initialization............................................................... 476
Figure 14.19 Sample Flowchart for Transmitting Serial Data ................................................... 477
Figure 14.20 Example of SCI Transmit Operation .................................................................... 478
Figure 14.21 Sample Flowchart for Receiving Serial Data ....................................................... 480
Figure 14.22 Example of SCI Receive Operation...................................................................... 482
Figure 14.23 Sample Flowchart for Transmitting/Receiving Serial Data.................................. 483
Figure 14.24 Receive Data Sampling Timing in Asynchronous Mode ..................................... 486
Figure 15.1

Block Diagram of Smart Card Interface............................................................... 490

Figure 15.2

Pin Connection Diagram for Smart Card Interface .............................................. 495

Figure 15.3

Data Format for Smart Card Interface .................................................................. 496

Figure 15.4

Waveform of Start Character................................................................................ 498

Figure 15.5

Initialization Flowchart (Example)....................................................................... 502

Figure 15.6

Transmission Flowchart ....................................................................................... 504

Figure 15.7

Reception Flowchart (Example) ........................................................................... 506

Figure 15.8

Receive Data Sampling Timing in Smart Card Mode .......................................... 508

Figure 15.9

Retransmission in SCI Receive Mode .................................................................. 509

Figure 15.10 Retransmission in SCI Transmit Mode ................................................................ 510
Figure 16.1

Block Diagram of SCIF........................................................................................ 512

Figure 16.2

SCPT[5]/SCK2 Pin .............................................................................................. 513

Figure 16.3

SCPT[4]/TxD2 Pin............................................................................................... 514

Figure 16.4

SCPT[4]/RxD2 Pin............................................................................................... 515

Figure 16.5

Sample Flowchart for SCIF Initialization ............................................................ 540

Figure 16.6

Sample Flowchart for Transmitting Serial Data ................................................... 542

Figure 16.7

Example of Transmit Operation (8-Bit Data, Parity, One Stop Bit)..................... 544

Figure 16.8

Example of Operation Using Modem Control (

CTS

)........................................... 544

Figure 16.9

Sample Flowchart for Receiving Serial Data ....................................................... 546

Figure 16.10 Sample Flowchart for Receiving Serial Data (cont)............................................. 547
Figure 16.11 Example of SCIF Receive Operation (8-Bit Data, Parity, One Stop Bit) ............. 549
Figure 16.12 Example of Operation Using Modem Control (

RTS

)........................................... 549

Figure 16.13 Receive Data Sampling Timing in Asynchronous Mode ..................................... 552
Figure 17.1

Block Diagram of IrDA........................................................................................ 556

Figure 17.2

SCPT[3]/SCK1 Pin .............................................................................................. 557

Figure 17.3

SCPT[2]/TxD1 Pin............................................................................................... 558

Figure 17.4

SCPT[2]/RxD1 Pin............................................................................................... 559

Figure 17.5

Transmit/Receive Operation................................................................................. 564

Figure 19.1

Port A ................................................................................................................... 587

Figure 19.2

Port B ................................................................................................................... 589

Figure 19.3

Port C ................................................................................................................... 591

Figure 19.4

Port D ................................................................................................................... 593

Figure 19.5

Port E.................................................................................................................... 595

Figure 19.6

Port F.................................................................................................................... 597

Figure 19.7

Port G ................................................................................................................... 599

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

Xinje XG Series User Manual preview
XG Series
Бренд: Xinje Страницы: 76
iWave iW-RainboW-G30D Hardware User'S Manual preview
iW-RainboW-G30D
Бренд: iWave Страницы: 89
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Бренд: Balluff Страницы: 12
Tektronix CTS 850 User Manual preview
CTS 850
Бренд: Tektronix Страницы: 178
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Бренд: Ubiquiti Страницы: 23
Atmel STK501 Specification Sheet preview
STK501
Бренд: Atmel Страницы: 2
Unex EVK-351 Quick Start Manual preview
EVK-351
Бренд: Unex Страницы: 27
Logicube ZCLONE User Manual preview
ZCLONE
Бренд: Logicube Страницы: 56
ekwb 3831109826140 User Manual preview
3831109826140
Бренд: ekwb Страницы: 11
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Бренд: PaloAlto Networks Страницы: 28
Antec KÜHLER H2O 920 Software Manual preview
KÜHLER H2O 920
Бренд: Antec Страницы: 6
Knowles IA611 Xplained Pro User Manual preview
IA611 Xplained Pro
Бренд: Knowles Страницы: 14
ADLINK Technology AMC-7000 User Manual preview
AMC-7000
Бренд: ADLINK Technology Страницы: 34
Datavideo NVW-150 Instruction Manual preview
NVW-150
Бренд: Datavideo Страницы: 71
DOD 410 SERIES II Owner'S Manual preview
410 SERIES II
Бренд: DOD Страницы: 12
Xaoc Devices NIN Operator'S Manual preview
NIN
Бренд: Xaoc Devices Страницы: 4
TRENDnet TEG-S3M8S15 Specifications preview
TEG-S3M8S15
Бренд: TRENDnet Страницы: 2
Emerson ControlWave Remote Ethernet I/O Product Data preview
ControlWave Remote Ethernet I/O
Бренд: Emerson Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды