manualshive.com logo in svg

Renesas SH7709S, Руководство по оборудованию

Hitachi SH7709S - многофункциональный процессор высокого качества для устройств сбора данных и встраиваемых систем. Получите бесплатно исчерпывающее Руководство по оборудованию для легкого использования и максимальной производительности. Скачайте его с manualshive.com.

Поделиться
Скачать
background image

Rev. 5.00, 09/03, page 364 of 760

•

 

Burst Mode, Level Detection

In the case of burst mode with level detection, the 

DREQ

 sampling timing is the same as in

cycle-steal mode.

For example, in figure 11.20, DMAC transfer begins, at the earliest, three cycles after the first
sampling is performed. The second sampling is started two cycles after the first. Subsequent
sampling operations are performed in the idle cycle following the end of the DMA transfer
cycle.

In burst mode, also, the DACK output period is the same as in cycle-steal mode.

•

 

Burst Mode, Edge Detection

In the case of burst mode with edge detection, 

DREQ

 sampling is only performed once.

For example, in figure 11.21, DMAC transfer begins, at the earliest, three cycles after the first
sampling is performed. After this, DMAC transfer is executed continuously until the number
of data transfers set in the DMATCR register have been completed. 

DREQ

 is not sampled

during this time.

To restart DMAC after it has been suspended by an NMI, first clear NMIF, then input an edge
request again.

In burst mode, also, the DACK output period is the same as in cycle-steal mode.

Содержание SH7709S








































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7709S

IBM 3270 Operation Manual preview
3270
Бренд: IBM Страницы: 86
TC Electronic ATAC Service Manual preview
ATAC
Бренд: TC Electronic Страницы: 55
Falcon 4G COMBO User Manual preview
4G COMBO
Бренд: Falcon Страницы: 24
Freescale Semiconductor MPC8349EA MDS Getting Started Manual preview
MPC8349EA MDS
Бренд: Freescale Semiconductor Страницы: 8
Swann NVRx-7300 series Quick Start Manual preview
NVRx-7300 series
Бренд: Swann Страницы: 9
S&T Kontron SMARC-sXEL User Manual preview
Kontron SMARC-sXEL
Бренд: S&T Страницы: 108
IEI Technology PulM-1G4T-I211 Quick Installation Manual preview
PulM-1G4T-I211
Бренд: IEI Technology Страницы: 2
Xantech CC62 Installation Instructions preview
CC62
Бренд: Xantech Страницы: 5
Softing TH LINK Installation Manual preview
TH LINK
Бренд: Softing Страницы: 16
National Instruments IMAQTM User Manual preview
IMAQTM
Бренд: National Instruments Страницы: 121
Waveshare High-Precision AD/DA Board User Manual preview
High-Precision AD/DA Board
Бренд: Waveshare Страницы: 8
ETAS ES1337.2 User Manual preview
ES1337.2
Бренд: ETAS Страницы: 29
Acces I/O products mPCIE-ADIO16-8F Series Hardware Manual preview
mPCIE-ADIO16-8F Series
Бренд: Acces I/O products Страницы: 13
M86 Security IR Web Filter User Manual preview
IR Web Filter
Бренд: M86 Security Страницы: 540
LevelOne ServCon FPS-3003 Quick Install Manual preview
ServCon FPS-3003
Бренд: LevelOne Страницы: 45
JETWAY JNLH61S-6C Series User Manual preview
JNLH61S-6C Series
Бренд: JETWAY Страницы: 36
Patton electronics 593/25, 593/45, 593/TB, RS-422, RS-485 User Manual preview
593/25, 593/45, 593/TB, RS-422, RS-485
Бренд: Patton electronics Страницы: 8
Alcatel-Lucent 1677 Brochure preview
1677
Бренд: Alcatel-Lucent Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды