Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 98

Страница: 98 / 240

Operation and Maintenance

5-4

9664-A2-GB20-00

March 2000

LED Descriptions

The following table identifies the alarms that cause the Alarm LED to light. See

Table 5-2

and

Table 5-3

for network interface and user data port LED information.

Table 5-1.

General Status LEDs

Label

Indication

Color

What It Means

Power and
Operational
Status

Green

ON –

FrameSaver unit has power and it is
operational.

OFF –

FrameSaver unit is in a power-on
self-test, or there is a failure.

ALM

Operational
Alarm ( Fail )

Red

ON –

FrameSaver unit has just been reset,
or an error or fault has been detected.

Error/fault/alarm conditions:

CTS Down

DLCI Down

DTR Down

LMI Down

Loss of Signal (LOS) at Network
Interface

Self-Test Failed

SLV Timeout

Two Level-1 Users Accessing
Device

OFF –

No failures have been detected.

These alarms appear on the System and
Test Status screen. See

Health and Status

Messages

for additional information.

TST

Test Mode

Yellow

ON –

Loopback or test pattern is in progress,
initiated locally, remotely, or from the
network.

OFF –

No tests are active.

Содержание FrameSaver SLV 9664











































































































































































































































Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9664, Руководство пользователя

Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды