Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 118

Страница: 118 / 240

Operation and Maintenance

5-24

9664-A2-GB20-00

March 2000

Service Level Verification Performance Statistics

These statistics appear when Service Level Verification (SLV) is selected from
the Performance Statistics menu.

Main Menu

→

Status

→

Performance Statistics

→

Service Level Verification

They only appear for the network interface and only if DLCIs are multiplexed.

Table 5-12.

Service Level Verification Performance Statistics (1 of 2)

Statistic

What It Indicates

Far End Circuit

Number of the multiplexed DLCI or VPI/VCI (Virtual Path
Identifier/Virtual Channel Identifier) at the other end of the
connection.

If the far-end circuit is a DLCI, the DLCI number (16 – 1007)
appears. If a VPI/VCI, the number is displayed as

xx,yyy,

xx being the VPI number (0 – 15) and

yyy being the VCI

number (32 – 2047).

None

appears if the unit has not communicated with the other

end.

Far End IP Addr

IP Address of the device at the other end of the multiplexed
DLCI connection.

None

appears if the FrameSaver unit has not communicated

with the other end, or if the device at the other end of the
multiplexed DLCI does not have an IP Address configured.

Dropped SLV
Responses

The number of SLV inband sample messages sent for which a
response from the far-end device has not been received.

Inbound Dropped
Frames

Total number of frames transmitted by the far-end device that
were dropped in transit.

The counts continue to increment until the maximum value is
reached (2

–2), then the count starts over.

The

SLV Delivery Ratio

option (see Table 3-2, Service Level

Verification Options) must be enabled for these statistics to
appear.

Above CIR

The number of frames transmitted by the far-end device that
were above the committed information rate and were
dropped in transit.

Within CIR

The number of frames transmitted by the far-end device that
were within the committed information rate, but were
dropped in transit.

Between CIR&EIR

The number of frames transmitted by the far-end device that
were between the committed information rate and excess
information rate, and were dropped in transit.

Above EIR

The number of frames transmitted by the far-end device that
were above the excess information rate and were dropped
in transit.

Содержание FrameSaver SLV 9664











































































































































































































































Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды

Paradyne FrameSaver SLV 9664, Руководство пользователя

Результаты поиска

Содержание FrameSaver SLV 9664

Отзывы:

Похожие инструкции для FrameSaver SLV 9664

Бренды по названию

Популярные бренды