Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 200 | Manualshive

Страница: 200 / 240

background image

SNMP MIBs and Traps, and RMON Alarm Defaults

B-14

9664-A2-GB20-00

March 2000

RMON Alarm and Event Defaults

The FrameSaver unit supports automatic generation of RMON alarm and event
information. Each alarm sets an SNMP variable to monitor. When the threshold
set for the monitored variable is exceeded, an SNMP trap or a log event is sent.

Event Defaults

Since all events sent are under the control of the FrameSaver unit, there is no
need to define multiple events for each alarm type, so only the following two
events need to be generated:

eventIndex

eventDescription

eventType

eventCommunity

1

Default SLV Rising Event

log-and-trap(4)

0

2

Default SLV Falling Event log-and-trap(4)

0

The alarm default tables starting on the next page show how each RMON default
alarm is set by the FrameSaver unit, shows the alarm and event types, the
interval used when generating alarms, and thresholds.

H

Physical Interface Alarm Defaults

H

Frame Relay Link Alarm Defaults

H

DLCI Alarm Defaults – Paradyne Area

H

DLCI Alarm Defaults – NetScout Area

See

Standards Compliance for SNMP Traps

for information about how traps

work, and

Traps: RMON-Specific

for traps specific to remote monitoring.

Rising Event Operation

If a rising threshold is crossed during the interval shown in a table (e.g., frames
dropped by the network), the event is armed and an alarm is generated at the
end of the interval. Only one alarm per event per interval is generated. The alarm
condition persists until the event has been disarmed (reset).

The event is disarmed when a falling threshold has been crossed and the rising
threshold has not been crossed during an interval, allowing the event to return to
its original disarmed state.

«
...
198
199
200
201
202
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

3CR860-95 - OfficeConnect Secure Router

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 26

Бренд: ICP DAS USA Страницы: 8

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

EdgeLens INT10G8LR56

Бренд: Garland Страницы: 30

Бренд: VCS Страницы: 118

Бренд: SyChip Страницы: 24

Бренд: BEC Страницы: 159

Бренд: Razer Страницы: 17

Бренд: Topcom Страницы: 16

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренд: Steren Страницы: 130

Бренд: ActiveEye Страницы: 35

Бренд: Tripp Lite Страницы: 3

Бренд: H3C Страницы: 4

Бренд: Moxa Technologies Страницы: 94

Бренд: Crestron Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды