Paradyne FrameSaver SLV 9664 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 240

background image

Configuration

3-33

9664-A2-GB20-00

March 2000

Setting Up Management and Communication Options

The following options can be selected from the Management and Communication
menu:

H

Node IP Options

H

Management PVC Options

H

General SNMP Management Options

H

Telnet and FTP Sessions Options

H

SNMP NMS Security Options

H

SNMP Traps and Trap Dial-Out Options

H

Communication Port Options

H

External Modem (COM Port) Options

Configuring Node IP Information

Select Node IP to display, add, or change the information necessary to support
general IP communications for the node (see

Table 3-9

). When deploying units to

remote sites, minimally configure the Node IP Address and Subnet Mask.

Main Menu

→

Configuration

→

Management and Communication

→

Node IP

This set of configuration options includes a Troubleshooting (TS) Management
Link feature to help service providers isolate device problems within their
networks. This feature allows Telnet or FTP access to the unit on this link.
Troubleshooting over this link is essentially transparent to customer operations.
No alarms or SNMP traps are generated to create nuisance alarms for the
customer.

TS_Management_Link is initially disabled in most models, but the link can be
enabled at any time. Any valid network Management PVC created on a standard
DLCI can be used. When enabled, a troubleshooting link can be accessed any
time the service provider requests access. An assigned security level can also
control access.

When a DLCI has been defined as the troubleshooting management link, the
link is identified in the status field at the bottom of the Management PVC Entry
screen with the

This PVC has been designated as the TS

Management Link

message.

NOTE:

T

he unit may come from the factory with a TS Management PVC already

set up (e.g., 980).

«
...
59
60
61
62
63
...
»

Содержание FrameSaver SLV 9664

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver SLV 9664

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 5

Бренд: Accelerated Страницы: 10

Бренд: Accelerated Страницы: 4

Бренд: IBM Страницы: 4

Бренд: Patton electronics Страницы: 8

Бренд: Ubiquiti Страницы: 22

UniFi UAP-AC-LR

Бренд: Ubiquiti Страницы: 28

Бренд: A10 Страницы: 52

Бренд: iDirect Страницы: 52

Бренд: TRENDnet Страницы: 2

Бренд: Allied Telesis Страницы: 22

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Бренд: ZyXEL Communications Страницы: 282

Бренд: IBM Страницы: 72

Бренд: Lantronix Страницы: 75

Бренд: H3C Страницы: 103

Бренд: ADTRAN Страницы: 2

Бренд: Airlinkplus Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды